Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0445204 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Check Bus 2 Line  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen.
·

CAN main bus line, CAN branch line or connector

·

Central gateway ECU (network gateway ECU)

·

Rear hybrid motor control inverter assembly

(for AWD)

·

Battery ECU assembly

·

Hybrid motor control inverter assembly

·

Hybrid vehicle control ECU

·

ECM

·

No. 5 global CAN junction connector

·

No. 10 global CAN junction connector



WIRING DIAGRAM

C422279E03
1.354,0.948 1.969,1.146 0.615,0.198 10 false PCNH 1.344,1.448 1.958,1.646 0.615,0.198 10 false PCNL 1.833,0.823 2.448,1.021 0.615,0.198 10 false 10 1.823,1.365 2.438,1.563 0.615,0.198 10 false 11 1.823,3.396 2.438,3.594 0.615,0.198 10 false 33 1.833,3.927 2.448,4.125 0.615,0.198 10 false 32 1.365,3.479 1.979,3.677 0.615,0.198 10 false CA2H 1.365,4.021 1.979,4.219 0.615,0.198 10 false CA2L 5.26,0.813 5.875,1.01 0.615,0.198 10 false CA4H 5.271,1.354 5.885,1.552 0.615,0.198 10 false CA4L 2.646,1.365 3.26,1.563 0.615,0.198 10 false 13 2.688,0.833 3.302,1.031 0.615,0.198 10 false 2 3.979,1.365 4.375,1.542 0.396,0.177 10 false 15 3.969,0.813 4.448,1.01 0.479,0.198 10 false 4 3.979,3.396 4.417,3.573 0.438,0.177 10 false 1 3.979,3.927 4.427,4.135 0.448,0.208 10 false 12 2.688,3.396 3.302,3.594 0.615,0.198 10 false 3 2.635,3.927 3.25,4.125 0.615,0.198 10 false 14 2.604,4.438 3.219,4.635 0.615,0.198 10 false O88 2.604,4.604 4.344,5.104 1.74,0.5 10 false No. 10 Global CAN Junction Connector 0.531,4.594 2.26,5.01 1.729,0.417 10 false Battery ECU Assembly 0.531,4.417 0.969,4.646 0.438,0.229 10 false z12 0.438,2.021 2.052,2.531 1.615,0.51 10 false Rear Hybrid Motor Control Inverter Assembly*1 0.438,1.854 0.802,2.115 0.365,0.26 10 false O74 4.958,0.823 5.354,1 0.396,0.177 10 false 26 4.969,1.365 5.365,1.542 0.396,0.177 10 false 25 4.927,1.844 5.542,2.042 0.615,0.198 10 false H40 4.917,2.01 6.865,2.448 1.948,0.438 10 false Central Gateway ECU (Network Gateway ECU) 5.51,5.104 5.667,5.302 0.156,0.198 10 false A 5.833,5.104 5.99,5.302 0.156,0.198 10 false B 0.313,5.417 2,5.615 1.688,0.198 10 false *1: for AWD

C444855E01
2.781,4.271 4.448,4.875 1.667,0.604 10 false No. 5 Global CAN Junction Connector 2.781,4.083 3.292,4.354 0.51,0.271 10 false H116 4.104,0.896 4.385,1.208 0.281,0.313 10 false 5 4.094,1.448 4.375,1.76 0.281,0.313 10 false 16 2.813,0.906 3.094,1.219 0.281,0.313 10 false 2 2.75,1.438 3.031,1.75 0.281,0.313 10 false 13 2.813,3.042 3.094,3.354 0.281,0.313 10 false 1 2.75,3.573 3.031,3.885 0.281,0.313 10 false 12 4.094,3.031 4.375,3.344 0.281,0.313 10 false 4 4.083,3.583 4.365,3.896 0.281,0.313 10 false 15 0.51,2.063 2.271,2.479 1.76,0.417 10 false Hybrid Motor Control Inverter Assembly 0.698,4.25 2.74,4.729 2.042,0.479 10 false ECM 5.188,4.26 7.042,4.948 1.854,0.688 10 false Hybrid Vehicle Control ECU 0.708,4.083 1.219,4.354 0.51,0.271 10 false A53 1.448,3.042 1.958,3.313 0.51,0.271 10 false CANH 1.458,3.583 1.969,3.854 0.51,0.271 10 false CANL 1.958,3.042 2.24,3.354 0.281,0.313 10 false 13 1.958,3.573 2.24,3.885 0.281,0.313 10 false 26 1.458,1.021 1.969,1.292 0.51,0.271 10 false CANH 1.479,1.531 1.99,1.802 0.51,0.271 10 false CANL 1.958,0.906 2.24,1.219 0.281,0.313 10 false 1 1.969,1.438 2.25,1.75 0.281,0.313 10 false 7 5.146,3.042 5.427,3.354 0.281,0.313 10 false 9 5.094,3.583 5.375,3.896 0.281,0.313 10 false 22 5.354,3.135 5.865,3.406 0.51,0.271 10 false CA1H 5.375,3.677 5.885,3.948 0.51,0.271 10 false CA1L 0.531,1.906 1.052,2.135 0.521,0.229 10 false A56 5.188,4.073 5.698,4.344 0.51,0.271 10 false H44 4.979,0.448 5.135,0.646 0.156,0.198 10 false B 4.656,0.438 4.813,0.635 0.156,0.198 10 false A

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.*1

*1: w/ Entry and Start System




HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C425195C69
1.51,0.073 1.927,0.323 0.417,0.25 2.094,0.885 2.708,1.688 true 2,0.896 2.552,1.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.125 2.063,0.323 0.458,0.198 10 false H40 2.583,1.906 3.052,2.125 0.469,0.219 10 false CA4H 2.719,1.698 3.198,1.865 0.479,0.167 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES

NG

50.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR SHORT IN CAN BUS LINES
a.
C425195C69
1.51,0.073 1.927,0.323 0.417,0.25 2.094,0.885 2.708,1.688 true 2,0.896 2.552,1.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.125 2.063,0.323 0.458,0.198 10 false H40 2.583,1.906 3.052,2.125 0.469,0.219 10 false CA4H 2.719,1.698 3.198,1.865 0.479,0.167 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Result
OK
NG



OK

3.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

35.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C47
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.292 5.729,0.563 0.417,0.271 6.302,1.615 6.573,2.021 true 2.479,1.313 3,2.115 true 2.396,1.302 2.865,2.344 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 3.042,2.073 3.594,2.271 0.552,0.198 10 false CA4L 6.604,1.99 7.156,2.188 0.552,0.198 10 false BAT 2.885,2.344 3.438,2.542 0.552,0.198 10 false CA4H 5.438,0.354 5.75,0.552 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-26 (CA4H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-25 (CA4L) - H3-16 (BAT)



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
4.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C48
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.125 5.729,0.396 0.417,0.271 5.427,1.042 6.042,0.604 true 2.479,1.292 3.042,2.073 true 2.406,1.292 2.927,2.396 true 4.073,0.094 4.385,0.292 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 3.094,2.031 3.646,2.229 0.552,0.198 10 false CA4L 6.083,0.51 6.635,0.708 0.552,0.198 10 false CG 2.948,2.365 3.5,2.563 0.552,0.198 10 false CA4H 5.427,0.177 5.74,0.375 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-26 (CA4H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-25 (CA4L) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the O88 No. 10 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
O88-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to No. 5 Global CAN Junction Connector
O88-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

7.CHECK VEHICLE TYPE

NG

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
7.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for AWD A
except AWD B



A

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

B

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Rear Hybrid Motor Control Inverter Assembly
O88-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)

NG

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Battery ECU Assembly
O88-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR

NG

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
O88-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Rear Hybrid Motor Control Inverter Assembly
O88-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
a.

Disconnect the z12 battery ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Battery ECU Assembly
O88-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-5 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to No. 10 Global CAN Junction Connector
H116-16 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Hybrid Motor Control Inverter Assembly
H116-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

NG

17.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Hybrid Vehicle Control ECU
H116-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

18.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to ECM
H116-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

19.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
17.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Disconnect the A56 hybrid motor control inverter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Hybrid Motor Control Inverter Assembly
H116-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

18.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Hybrid Vehicle Control ECU
H116-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

19.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A53 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to ECM
H116-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the O88 No. 10 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
O88-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

21.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

25.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
21.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to No. 5 Global CAN Junction Connector
O88-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

22.CHECK VEHICLE TYPE

NG

28.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
22.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for AWD A
except AWD B



A

23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

B

24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Rear Hybrid Motor Control Inverter Assembly
O88-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)

NG

26.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Battery ECU Assembly
O88-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR

NG

27.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
25.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
O88-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

26.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Rear Hybrid Motor Control Inverter Assembly
O88-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

27.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
a.

Disconnect the z12 battery ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88,H3)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O88-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Battery ECU Assembly
O88-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)

28.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-5 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to No. 10 Global CAN Junction Connector
H116-16 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

29.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)

29.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Hybrid Motor Control Inverter Assembly
H116-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

30.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

NG

32.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
30.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Hybrid Vehicle Control ECU
H116-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

31.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

33.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
31.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to ECM
H116-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

34.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
32.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Disconnect the A56 hybrid motor control inverter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Hybrid Motor Control Inverter Assembly
H116-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

33.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Hybrid Vehicle Control ECU
H116-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

34.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A53 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116,H3)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H116-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to ECM
H116-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)

35.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the O88 No. 10 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

O88-4 (CANH) - O88-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

36.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

40.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
36.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

O88-1 (CANH) - O88-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 5 Global CAN Junction Connector



Result:
Result
OK
NG



OK

37.CHECK VEHICLE TYPE

NG

43.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
37.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for AWD A
except AWD B



A

38.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

B

39.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
38.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

O88-2 (CANH) - O88-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Rear Hybrid Motor Control Inverter Assembly



Result:
Result
OK
NG



OK

39.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)

NG

41.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
39.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

O88-3 (CANH) - O88-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Battery ECU Assembly



Result:
Result
OK
NG



OK

REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR

NG

42.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
40.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

O88-4 (CANH) - O88-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

41.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

O88-2 (CANH) - O88-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Rear Hybrid Motor Control Inverter Assembly



Result:
Result
OK
NG



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

42.CHECK FOR SHORT IN CAN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)
a.

Disconnect the z12 battery ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

O88-3 (CANH) - O88-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Battery ECU Assembly



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - BATTERY ECU ASSEMBLY)

43.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H116 No. 10 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

H116-5 (CANH) - H116-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 10 Global CAN Junction Connector



Result:
Result
OK
NG



OK

44.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)

44.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

H116-2 (CANH) - H116-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Hybrid Motor Control Inverter Assembly



Result:
Result
OK
NG



OK

45.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

NG

47.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
45.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

H116-4 (CANH) - H116-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Hybrid Vehicle Control ECU



Result:
Result
OK
NG



OK

46.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

48.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
46.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

H116-1 (CANH) - H116-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to ECM



Result:
Result
OK
NG



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

49.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
47.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)
a.

Disconnect the A56 hybrid motor control inverter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

H116-2 (CANH) - H116-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Hybrid Motor Control Inverter Assembly



Result:
Result
OK
NG



OK

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

48.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

H116-4 (CANH) - H116-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Hybrid Vehicle Control ECU



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

49.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A53 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

H116-1 (CANH) - H116-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to ECM



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)

50.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 10 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

51.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
51.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the O88 No. 10 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

O88-4 (CANH) - O88-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

52.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

52.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 10 GLOBAL CAN JUNCTION CONNECTOR - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(O88)Location & Routing

Click Connector(O88)Body>Floor Wire>No. 10 Global CAN Junction Connector

O88-1 (CANH) - O88-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 5 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE NO. 10 GLOBAL CAN JUNCTION CONNECTOR

NG

53.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
53.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H116 No. 5 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

H116-5 (CANH) - H116-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 10 Global CAN Junction Connector



Result:
Result
OK
NG



OK

54.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - NO. 10 GLOBAL CAN JUNCTION CONNECTOR)

54.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H116)Location & Routing

Click Connector(H116)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 5 Global CAN Junction Connector

H116-1 (CANH) - H116-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to ECM



Result:
Result
OK
NG



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

55.CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM)
55.CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM)
a.

Disconnect the A53 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(A53)Location & Routing

Click Connector(A53)Engine Compartment>Engine Room Main Wire>ECM

A53-13 (CANH) - A53-26 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 5 Global CAN Junction Connector



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)