Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0445204 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Check Bus 3 Line  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen.
·

CAN main bus line, CAN branch line or connector

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly

·

Meter mirror sub-assembly

(w/ Headup Display)

·

Telematics transceiver

(w/ Telematics Transceiver)

·

Combination meter assembly

·

No. 4 global CAN junction connector



WIRING DIAGRAM

C430861E10
0.146,1.844 2.094,2.198 1.948,0.354 10 false Central Gateway ECU (Network Gateway ECU) 0.156,1.688 0.552,1.875 0.396,0.188 10 false H40 1.26,0.677 1.729,0.844 0.469,0.167 10 false CA3H 1.271,1.177 1.74,1.344 0.469,0.167 10 false CA3L 1.688,0.667 2,0.865 0.313,0.198 10 false 30 1.719,1.177 2.031,1.375 0.313,0.198 10 false 29 2.833,0.708 2.99,0.906 0.156,0.198 10 false 1 2.74,1.167 3.052,1.365 0.313,0.198 10 false 12 4.104,0.698 4.26,0.896 0.156,0.198 10 false 3 4.094,1.167 4.406,1.365 0.313,0.198 10 false 14 5.26,0.698 5.573,0.896 0.313,0.198 10 false 13 5.26,1.177 5.573,1.375 0.313,0.198 10 false 14 5.521,0.792 6.135,0.99 0.615,0.198 10 false CANH 5.521,1.271 6.135,1.469 0.615,0.198 10 false CANL 5.365,1.688 5.823,1.885 0.458,0.198 10 false H80 5.365,1.844 7.073,2.271 1.708,0.427 10 false Radio and Display Receiver Assembly 2.823,3.156 2.979,3.354 0.156,0.198 10 false 4 2.76,3.635 3.073,3.833 0.313,0.198 10 false 15 1.104,3.25 1.719,3.448 0.615,0.198 10 false CANP 1.104,3.74 1.719,3.938 0.615,0.198 10 false CANN 1.583,3.156 1.896,3.354 0.313,0.198 10 false 25 1.573,3.646 1.885,3.844 0.313,0.198 10 false 26 0.302,4.146 0.76,4.344 0.458,0.198 10 false H85 0.302,4.302 2.469,4.667 2.167,0.365 10 false Telematics Transceiver*1 5.51,3.25 5.969,3.469 0.458,0.219 10 false MPX1 5.51,3.719 5.969,3.938 0.458,0.219 10 false MPX2 4.094,3.167 4.25,3.365 0.156,0.198 10 false 5 4.073,3.635 4.385,3.833 0.313,0.198 10 false 16 5.26,3.156 5.573,3.354 0.313,0.198 10 false 12 5.26,3.635 5.573,3.833 0.313,0.198 10 false 13 5.052,4.146 5.51,4.344 0.458,0.198 10 false H61 5.052,4.302 6.885,4.552 1.833,0.25 10 false Meter Mirror Sub-assembly*2 4.094,5.625 4.25,5.823 0.156,0.198 10 false 2 4.073,6.083 4.385,6.281 0.313,0.198 10 false 13 5.323,5.625 5.479,5.823 0.156,0.198 10 false 9 5.25,6.094 5.563,6.292 0.313,0.198 10 false 25 5.521,5.635 6.135,5.833 0.615,0.198 10 false CANH 5.521,6.094 6.135,6.292 0.615,0.198 10 false CANL 5.208,6.625 5.521,6.823 0.313,0.198 10 false H6 5.208,6.781 7.156,7.01 1.948,0.229 10 false Combination Meter Assembly 2.344,6.625 2.958,6.823 0.615,0.198 10 false H115 2.344,6.792 4.813,7.073 2.469,0.281 10 false No. 4 Global CAN Junction Connector 0.167,5.979 3.073,6.177 2.906,0.198 10 false *1: w/ Telematics Transceiver 0.167,6.302 3.073,6.5 2.906,0.198 10 false *2: w/ Headup Display

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C425195C70
1.51,0.073 1.927,0.323 0.417,0.25 0.469,1.667 1.083,0.896 true 1.198,0.896 0.833,1.885 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.125 2.063,0.323 0.458,0.198 10 false H40 0.531,1.885 1,2.104 0.469,0.219 10 false CA3L 0.104,1.677 0.583,1.844 0.479,0.167 10 false CA3H
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-30 (CA3H) - H40-29 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES

NG

41.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR SHORT IN CAN BUS LINES
a.
C425195C70
1.51,0.073 1.927,0.323 0.417,0.25 0.469,1.667 1.083,0.896 true 1.198,0.896 0.833,1.885 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.125 2.063,0.323 0.458,0.198 10 false H40 0.531,1.885 1,2.104 0.469,0.219 10 false CA3L 0.104,1.677 0.583,1.844 0.479,0.167 10 false CA3H
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-30 (CA3H) - H40-29 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Result
OK
NG



OK

3.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

29.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C49
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.292 5.729,0.563 0.417,0.271 0.573,2.125 1.552,1.313 true 1.208,2.167 1.656,1.313 true 6.521,2.052 6.292,1.615 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 0.927,2.177 1.479,2.375 0.552,0.198 10 false CA3L 6.51,2.073 7.063,2.271 0.552,0.198 10 false BAT 0.198,2.125 0.75,2.323 0.552,0.198 10 false CA3H 5.438,0.344 5.75,0.542 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-30 (CA3H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-29 (CA3L) - H3-16 (BAT)



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

17.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
4.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C50
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.135 5.729,0.406 0.417,0.271 0.708,2.031 1.573,1.302 true 1.302,2.167 1.656,1.302 true 5.385,1.031 4.896,0.604 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 1.01,2.188 1.563,2.385 0.552,0.198 10 false CA3L 4.646,0.51 5.198,0.708 0.552,0.198 10 false CG 0.333,2.042 0.885,2.24 0.552,0.198 10 false CA3H 5.427,0.198 5.74,0.396 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-30 (CA3H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-29 (CA3L) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H115-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Radio and Display Receiver Assembly
H115-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

7.CHECK VEHICLE TYPE

NG

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
7.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)

B

9.CHECK VEHICLE TYPE
8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-5 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Meter Mirror Sub-assembly
H115-16 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

9.CHECK VEHICLE TYPE

NG

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
9.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Telematics Transceiver A
w/o Telematics Transceiver B



A

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)

B

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Telematics Transceiver
H115-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Combination Meter Assembly
H115-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Specified Condition

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H115-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Radio and Display Receiver Assembly
H115-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
a.

Disconnect the H61 meter mirror sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-5 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Meter Mirror Sub-assembly
H115-16 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
a.

Disconnect the H85 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Telematics Transceiver
H115-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)

16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Combination Meter Assembly
H115-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

17.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H115-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

18.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
18.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Radio and Display Receiver Assembly
H115-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

19.CHECK VEHICLE TYPE

NG

25.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
19.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)

B

21.CHECK VEHICLE TYPE
20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-5 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Meter Mirror Sub-assembly
H115-16 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

21.CHECK VEHICLE TYPE

NG

26.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
21.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Telematics Transceiver A
w/o Telematics Transceiver B



A

22.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)

B

23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
22.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Telematics Transceiver
H115-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

27.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Combination Meter Assembly
H115-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

28.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H115-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

25.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Radio and Display Receiver Assembly
H115-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

26.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
a.

Disconnect the H61 meter mirror sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-5 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Meter Mirror Sub-assembly
H115-16 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)

27.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
a.

Disconnect the H85 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Telematics Transceiver
H115-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)

28.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115,H3)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H115-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Combination Meter Assembly
H115-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

29.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-1 (CANH) - H115-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

30.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

36.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
30.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-3 (CANH) - H115-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Radio and Display Receiver Assembly



Result:
Result
OK
NG



OK

31.CHECK VEHICLE TYPE

NG

37.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
31.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

32.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)

B

33.CHECK VEHICLE TYPE
32.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-5 (CANH) - H115-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Meter Mirror Sub-assembly



Result:
Result
OK
NG



OK

33.CHECK VEHICLE TYPE

NG

38.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
33.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Telematics Transceiver A
w/o Telematics Transceiver B



A

34.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)

B

35.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
34.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-4 (CANH) - H115-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Telematics Transceiver



Result:
Result
OK
NG



OK

35.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

39.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
35.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-2 (CANH) - H115-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Combination Meter Assembly



Result:
Result
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

40.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
36.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-1 (CANH) - H115-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

37.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-3 (CANH) - H115-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Radio and Display Receiver Assembly



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

38.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
a.

Disconnect the H61 meter mirror sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-5 (CANH) - H115-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Meter Mirror Sub-assembly



Result:
Result
OK
NG



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)

39.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
a.

Disconnect the H85 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-4 (CANH) - H115-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Telematics Transceiver



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)

40.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-2 (CANH) - H115-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Combination Meter Assembly



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

41.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-30 (CA3H) - H40-29 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 4 Global CAN Junction Connector



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

42.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
42.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-1 (CANH) - H115-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

43.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

43.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H115)Location & Routing

Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connector

H115-2 (CANH) - H115-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Combination Meter Assembly



Result:
Result
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

44.CHECK FOR OPEN IN CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY)
44.CHECK FOR OPEN IN CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H6)Location & Routing

Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

H6-9 (CANH) - H6-25 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)