Each speed sensor detects the wheel speed and sends the signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for ABS control.
The output voltage values shown below are for when the vehicle wire harnesses are connected to the skid control ECU (brake booster with master cylinder assembly) and the speed sensors.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C05001F | Left Front Wheel Speed Sensor Circuit Intermittent | Any of the following is detected:
·
An open in the sensor signal of a malfunctioning wheel occurs 255 times or more. ·
At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds. ·
At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more. |
·
Front speed sensor LH ·
Speed sensor installation ·
Wire harness and connector ·
Front speed sensor rotor LH (front axle hub sub-assembly LH) ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake/EPB | A |
After replacing the skid control ECU (brake booster with master cylinder assembly), perform "Calibration".
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Tester Display |
|---|
| FL Speed Sensor Voltage Open |
Check for any momentary interruptions in the wire harness and connectors.
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FL Wheel Speed |
Check the front speed sensor LH output value.
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Check if the same DTC is output
| Result | Proceed to |
|---|---|
| C05001F is not output | A |
| C05001F is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Turn the ignition switch off.
Procedure1
| *1 | Front Speed Sensor LH |
| *a | Correct |
| *b | Incorrect |
| *c | 8.5 Nm |
| *d | No clearance |
Check the front speed sensor LH installation.
There is no clearance between the front speed sensor LH and steering knuckle.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the front speed sensor LH and the component with the front speed sensor rotor LH.
for front speed sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor LH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL
Procedure1
Check the front speed sensor LH tip and front speed sensor rotor LH.
No scratches, oil, or foreign matter on the front speed sensor LH tip and front speed sensor rotor LH.
If there is oil or foreign matter on the front speed sensor LH, clean the front speed sensor LH.
If the front speed sensor LH is damaged, replace the front speed sensor LH with a new one.
Do not use parts cleaner when cleaning the front speed sensor rotor LH.
If the front speed sensor rotor LH is damaged, replace the front speed sensor rotor LH with a new one.
The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.
If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A22 front speed sensor LH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A22,A38)Location & Routingewd_type=routing;type=c,c;code=A22,A38 Click Connector(A22)Engine Compartment>Engine Room Main Wire>Front Speed Sensor LHewd_type=component;type=c;code=A22;pinno=1,2 Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assemblyewd_type=component;type=c;code=A38;pinno=31,32 |
||
| A22-1 (FL+) - A38-31 (FL+) | Always | Below 1 Ω |
| A22-1 (FL+) or A38-31 (FL+) - Body ground | Always | 10 kΩ or higher |
| A22-2 (FL-) - A38-32 (FL-) | Always | Below 1 Ω |
| A22-2 (FL-) or A38-32 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Turn the ignition switch to ON.
Procedure2
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A22)Location & Routingewd_type=routing;type=c;code=A22 Click Connector(A22)Engine Compartment>Engine Room Main Wire>Front Speed Sensor LHewd_type=component;type=c;code=A22;pinno=1 |
||
| A22-1 (FL+) - Body ground | Ignition switch ON | 8 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG