Refer to DTC C05001F.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C050023 | Left Front Wheel Speed Sensor Signal Stuck Low | Any of the following is detected:
·
At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.*1 ·
At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.*2 ·
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 30 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).*1 ·
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).*2 ·
At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. |
·
Front speed sensor LH ·
Speed sensor installed improperly ·
Front speed sensor rotor LH (front axle hub sub-assembly LH) ·
Wire harness or connector |
Brake/EPB | A |
*1: for AWD
*2: for 2WD
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
| *1 | Front Speed Sensor LH |
| *a | Correct |
| *b | Incorrect |
| *c | 8.5 Nm |
| *d | No clearance |
Check the front speed sensor LH installation.
There is no clearance between the front speed sensor LH and front axle carrier sub-assembly.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the front speed sensor LH.
Procedure1
Check the front speed sensor LH tip.
The front speed sensor LH tip is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor LH, clean the front speed sensor LH.
If the front speed sensor LH is damaged, replace the front speed sensor LH with a new one.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FL Wheel Speed |
Check the front speed sensor RH output value.
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the A22 front speed sensor LH connector.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A22,A38)Location & Routingewd_type=routing;type=c,c;code=A22,A38 Click Connector(A22)Engine Compartment>Engine Room Main Wire>Front Speed Sensor LHewd_type=component;type=c;code=A22;pinno=1,2 Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assemblyewd_type=component;type=c;code=A38;pinno=31,32 |
||
| A22-1 (FL+) - A38-31 (FL+) | Always | Below 1 Ω |
| A22-1 (FL+) or A38-31 (FL+) - Body ground | Always | 10 kΩ or higher |
| A22-2 (FL-) - A38-32 (FL-) | Always | Below 1 Ω |
| A22-2 (FL-) or A38-32 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the component with the front speed sensor rotor LH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL
Procedure1
Check the front speed sensor rotor LH.
The front speed sensor rotor LH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor rotor LH, clean the front speed sensor rotor LH.
Do not use parts cleaner when cleaning the front speed sensor rotor LH.
If the front speed sensor rotor LH is damaged, replace the front speed sensor rotor LH with a new one.
The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.
If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The front speed sensor rotor LH is damaged.) | B |
| NG (There is foreign matter on the front speed sensor rotor LH.) | C |
Post-procedure1
None
A
B
C