Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0446873 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C051223  Right Rear Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C05121F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C05121F

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C051223 Right Rear Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
·

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.*1

·

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.*2

·

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) for 30 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).*1

·

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except when both rear speed sensors are 0 km/h (0 mph)).*2

·

At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.


·

Rear speed sensor RH*1

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)*2

·

Speed sensor installed improperly

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Wire harness or connector


Brake/EPB A

*1: for AWD

*2: for 2WD


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for 2WD A
for AWD B



A

2.CHECK REAR SPEED SENSOR RH INSTALLATION

B

6.CHECK REAR SPEED SENSOR LH INSTALLATION
2.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C210569C18
1.208,1.365 0.979,1.167 false 0.833,1.833 1.25,2.083 0.417,0.25 10 false *b 2.344,1.833 2.677,2.083 0.333,0.25 10 false *c 1.26,1.313 1.594,1.49 0.333,0.177 10 false *a
*a No clearance
*b Correct
*c Incorrect


Check the rear speed sensor RH installation.

OK:

There is no clearance between the rear speed sensor RH and the rear axle hub and bearing assembly RH.


HINT:

The rear speed sensor rotor RH and rear speed sensor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor rotor RH needs to be replaced, replace the rear axle hub and bearing assembly RH with rear speed sensor RH.


Result:
Proceed to
OK
NG




OK

3.READ VALUE USING GTS (RR WHEEL SPEED)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

3.READ VALUE USING GTS (RR WHEEL SPEED)
a.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RR Wheel Speed
50003 435 15

b.

Check the rear speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
4.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the u2 and uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(u2,uO1)Location & Routing

Click Connector(u2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor RH (Rear Axle Hub & Bearing Assembly RH)

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

u2-2 (RR+) - uO1-4 (RR+) Always Below 1 Ω
u2-2 (RR+) or uO1-4 (RR+) - Body ground and other terminals Always 10 kΩ or higher
u2-1 (RR-) - uO1-3 (RR-) Always Below 1 Ω
u2-1 (RR-) or uO1-3 (RR-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO1,A38)Location & Routing

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

uO1-4 (RR+) - A38-7 (RR+) Always Below 1 Ω
uO1-4 (RR+) or A38-7 (RR+) - Body ground and other terminals Always 10 kΩ or higher
uO1-3 (RR-) - A38-8 (RR-) Always Below 1 Ω
uO1-3 (RR-) or A38-8 (RR-) - Body ground and other terminals Always 10 kΩ or higher


HINT:

The rear speed sensor RH is incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH needs to be replaced, replace the rear axle hub and bearing assembly RH.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C168336C47
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Speed Sensor RH
*a OK
*b NG
*c 8.5 N*m (87 kgf*cm, 75 in.*lbf)
*d No Clearance


Check the rear speed sensor RH installation.

OK:

There is no clearance between the sensor and the rear axle carrier.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)


Result:
Proceed to
OK
NG




OK

7.CHECK REAR SPEED SENSOR LH AND REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE REAR SPEED SENSOR RH

7.CHECK REAR SPEED SENSOR LH AND REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

Pre-procedure1

a.

Remove the rear speed sensor RH and the component with the rear speed sensor rotor RH.

HINT:

for Rear Speed Sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for AWD)>REMOVAL

for Rear Speed Sensor Rotor RH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for AWD)>REMOVAL



Procedure1

a.

Check the rear speed sensor tip RH and rear speed sensor rotor RH.

OK:

The rear speed sensor tip RH and rear speed sensor rotor RH are free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor RH, clean the rear speed sensor RH and then check the rear speed sensor rotor RH.

·

If the rear speed sensor RH is damaged, replace the rear speed sensor RH with a new one.

·

Check the rear speed sensor RH signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.READ VALUE USING GTS (RR WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SPEED SENSOR LH AND REAR SPEED SENSOR ROTOR LH

8.READ VALUE USING GTS (RR WHEEL SPEED)
a.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RR Wheel Speed
50003 435 15

b.

Check the rear speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

9.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
9.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the u2 and uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(u2,uO1)Location & Routing

Click Connector(u2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor RH (Rear Axle Hub & Bearing Assembly RH)

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

u2-1 (+) - uO1-4 (RR+) Always Below 1 Ω
u2-1 (+) or uO1-4 (RR+) - Body ground and other terminals Always 10 kΩ or higher
u2-2 (-) - uO1-3 (RR-) Always Below 1 Ω
u2-2 (-) or uO1-3 (RR-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

10.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO1,A38)Location & Routing

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

uO1-4 (RR+) - A38-7 (RR+) Always Below 1 Ω
uO1-4 (RR+) or A38-7 (RR+) - Body ground and other terminals Always 10 kΩ or higher
uO1-3 (RR-) - A38-8 (RR-) Always Below 1 Ω
uO1-3 (RR-) or A38-8 (RR-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

11.CHECK REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
a.

Remove the rear speed sensor RH and the component with the rear speed sensor rotor RH.

HINT:

for Rear Speed Sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for AWD)>REMOVAL

for Rear Speed Sensor Rotor RH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for AWD)>REMOVAL



b.

Check the rear speed sensor rotor RH.

OK:

The rear speed sensor rotor RH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor rotor RH, clean the rear speed sensor rotor RH.

·

If the rear speed sensor rotor RH is damaged, replace the rear speed sensor rotor RH with a new one.

·

Check the rear speed sensor RH signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>TEST MODE PROCEDURE



HINT:
·

The rear speed sensor rotor RH is incorporated into the rear axle hub and bearing assembly RH.

·

If the rear speed sensor rotor RH needs to be replaced, replace it together with the rear axle hub and bearing assembly RH.




Result:
Result Proceed to
OK A
NG (The rear speed sensor rotor RH is damaged.) B
NG (There is foreign matter on the rear speed sensor rotor RH.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

C

CLEAN REAR SPEED SENSOR ROTOR RH