Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat) › 2020.08–2021.07
RM3700E _58 Vehicle Interior _092990 SEAT _0446933 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B597804N01
0.083,0.083 2.417,2.333 2.333,2.25 0.167,1.167 2.083,2.167 1.917,1 6.49,0.271 6.823,0.271 false 6.458,0.604 6.792,0.604 false 4.833,0.458 5.167,0.458 false 5.063,2.083 5.396,2.083 false 0.469,1.688 0.802,1.688 false 0.625,0.583 0.958,0.583 false 0.927,3.708 1.26,3.708 false 1.625,4.125 1.958,4.125 false 5.604,2.948 5.938,2.948 false 6.354,3.333 6.688,3.333 false 2.302,2.76 2.615,2.958 0.313,0.198 10 false x4 6.292,0.156 6.573,0.51 0.281,0.354 18 false 1 6.281,0.479 6.563,0.833 0.281,0.354 18 false 2 5.208,0.333 5.49,0.688 0.281,0.354 18 false 3 0.729,3.573 1.01,3.927 0.281,0.354 18 false 4 1.427,4 1.708,4.354 0.281,0.354 18 false 5 5.99,2.792 6.271,3.146 0.281,0.354 18 false 6 6.74,3.188 7.021,3.542 0.281,0.354 18 false 7 0.292,1.542 0.573,1.896 0.281,0.354 18 false 8 0.438,0.438 0.719,0.792 0.281,0.354 18 false 9 5.625,1.927 6.083,2.26 0.458,0.333 18 false 10 0.167,0.167 0.542,0.406 0.375,0.24 12 false *A 0.25,1.26 0.625,1.5 0.375,0.24 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 FRONT SEAT HEADREST ASSEMBLY 71910A - - -
4 FRONT SEAT TRACK BRACKET OUTER COVER 72123A - - -
5 FRONT SEAT TRACK BRACKET INNER COVER 72127A - - -
6 SEAT TRACK BRACKET OUTER COVER 72137 - - -
7 SEAT TRACK BRACKET INNER COVER 72157A - - -
8 FRONT SEAT UNDER TRAY 71753 - - -
9 FRONT SEAT CUSHION PROTECTOR 71537A - - -
10 FRONT SEAT ASSEMBLY - (Click here) - -

*A for front Passenger Seat *B w/ Under Tray

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat inner belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
B585480

Wear protective gloves. Sharp areas on the parts may injure your hands.


NOTICE:

If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad, separate type front seatback cover and front seatback pad with cover with the necessary parts in accordance with the extent of the collision damage.


HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the driver side and front passenger side.

·

The procedure listed below is for the driver side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B473126

Be sure to read Precaution thoroughly before servicing.(w/ Front Seat Side Airbag)

(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 71910A 3.REMOVE FRONT SEAT HEADREST ASSEMBLY

a.
B597805


Hide 72123A 4.REMOVE FRONT SEAT TRACK BRACKET OUTER COVER

a.
B597806


Hide 72127A 5.REMOVE FRONT SEAT TRACK BRACKET INNER COVER

a.
B597807


Hide 72137 6.REMOVE SEAT TRACK BRACKET OUTER COVER

a.
B597808


Hide 72157A 7.REMOVE SEAT TRACK BRACKET INNER COVER

a.
B597809


Hide 71753 8.REMOVE FRONT SEAT UNDER TRAY (w/ Under Tray)

a.
B597810C01
0,0 0,0 false
V113147

Remove in this Direction (1) - -



Hide 71537A 9.REMOVE FRONT SEAT CUSHION PROTECTOR (for Front Passenger Seat)

a.
B597811C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3) - -



Hide 10.REMOVE FRONT SEAT ASSEMBLY

a.
B597812C01
0.167,3.833 3.25,5.75 3.083,1.917 2,1.833 5.083,3.75 3.083,1.917 0.292,0.146 0.573,0.5 0.281,0.354 18 false i 3.573,0.167 4.146,0.531 0.573,0.365 18 false ii, iii 3.833,4.115 4.406,4.479 0.573,0.365 18 false iv, v 2.375,1.885 3.167,2.25 0.792,0.365 18 false vi, vii 0.625,3.885 1.417,4.25 0.792,0.365 18 false vi, vii 2.083,1.917 2.458,2.156 0.375,0.24 12 false *A 0.25,3.917 0.625,4.156 0.375,0.24 12 false *B
*A for Driver Seat *A for Front Passenger Seat


i.

Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly.


ii.

Operate the seat track adjusting handle to move the front seat assembly to the rearmost position.


iii.

Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly.


iv.

Operate the seat track adjusting handle to move the front seat assembly to the center position.


v.

Operate the reclining adjuster release handle and move the seatback to the upright position.


vi.

Disengage the clamp and disconnect the connectors.


vii.

Disconnect the front seat airbag assembly connector under the front seat assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




b.
B597813N01
0.375,0.01 0.656,0.365 0.281,0.354 18 false i

i.

Remove the front seat assembly as shown in the illustration.

NOTICE:
·

2 or more people are required when carrying the front seat assembly out of the vehicle.

·

Protect the front seat leg.

·

Be careful not to damage the front seat assembly, body exterior or body interior.