The forward recognition camera receives LTA main switch signals from the steering pad switch assembly.
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One time recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT
During the steering pad switch assembly check, check the precautions for the airbag system since the horn button assembly is removed during servicing. (installation/removal of parts, checks, replacement, etc.)
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| LDA Control | Whether lane tracing assist system control is permitted or not | Prohibit or Permit | Prohibit: Lane tracing assist system control not possible
Permit: Lane tracing assist system control possible |
- |
| Tester Display |
|---|
| LDA Control |
| Result | Proceed to |
|---|---|
| Data List value changes when LTA Main Switch is operated | A |
| Data List value does not change when LTA Main Switch is operated | B |
A
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>LANE TRACING ASSIST SYSTEM>PROBLEM SYMPTOMS TABLE
B
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H60 spiral cable sub-assembly connector.
Disconnect the V10 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H60,V10)Location & Routingewd_type=routing;type=c,c;code=H60,V10 Click Connector(H60)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H60;pinno=6 Click Connector(V10)Body>No. 1 Roof Wire>Forward Recognition Cameraewd_type=component;type=c;code=V10;pinno=3 |
||
| H60-6 (DIST) - V10-3 (LKSW) | Always | Below 1 Ω |
| H60-6 (DIST) or V10-3 (LKSW) - Body ground | Always | 10 kΩ or higher |
Connect the V10 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for HV Model | A |
| for Gasoline Model | B |
A
B
Disconnect the H60 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H60)Location & Routingewd_type=routing;type=c;code=H60 Click Connector(H60)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H60;pinno=2 |
||
| H60-2 (ECC) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H60 spiral cable sub-assembly connector.
Disconnect the A54 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H60,A54)Location & Routingewd_type=routing;type=c,c;code=H60,A54 Click Connector(H60)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H60;pinno=2 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=28 |
||
| H60-2 (ECC) - A54-28 (ECCS) | Always | Below 1 Ω |
| H60-2 (ECC) or A54-28 (ECCS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG