Home › Drivetrain › CLUTCH › CLUTCH STROKE SENSOR (for LHD) › from 2021.07
RM3700E _52 Drivetrain _104786 CLUTCH _0480195 CLUTCH STROKE SENSOR(for LHD) A

CLUTCH  CLUTCH STROKE SENSOR(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C459844N01
6.604,0.229 6.865,0.229 false 6.625,0.688 6.844,0.688 false 5,2.01 5,2.302 false 3.396,0.531 3.76,0.531 false 2.51,0.885 2.51,1.438 2.51,1.438 2.656,1.438 false 6.417,0.063 6.698,0.417 0.281,0.354 18 false 1 6.417,0.521 6.698,0.875 0.281,0.354 18 false 2 4.938,2.313 5.219,2.667 0.281,0.354 18 false 3 6.354,2.167 6.667,2.365 0.313,0.198 10 false x2 3.833,0.375 4.115,0.729 0.281,0.354 18 false 4 3,0.583 3.313,0.781 0.313,0.198 10 false x2 2.99,1.281 3.271,1.635 0.281,0.354 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
4 BRAKE PEDAL RETURN SPRING 47101A - - -
5 CLUTCH PEDAL STROKE SENSOR ASSEMBLY 89280 (Click here) - -

CAUTION / NOTICE / HINT

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 47101A 4.REMOVE BRAKE PEDAL RETURN SPRING

Hide 89280 5.REMOVE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

a.
C459845N01
0.115,0.01 0.281,0.292 0.167,0.281 18 true i 3.865,0.01 4,0.365 0.135,0.354 18 true ii

i.

Disconnect the clutch pedal stroke sensor assembly connector.


ii.

Remove the 2 nuts and clutch pedal stroke sensor assembly from the pedal support assembly.

NOTICE:
·

Do not drop the clutch pedal stroke sensor assembly.

·

If the clutch pedal stroke sensor assembly has been dropped, replace the clutch pedal stroke sensor assembly with a new one.