Home › Drivetrain › CLUTCH › CLUTCH STROKE SENSOR (for RHD) › from 2021.07
RM3700E _52 Drivetrain _104786 CLUTCH _0480196 CLUTCH STROKE SENSOR(for RHD) A

CLUTCH  CLUTCH STROKE SENSOR(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C440374N03
2.74,1.104 2.573,1.104 2.573,1.104 2.458,0.833 false 5.958,2.01 5.792,2.01 5.792,2.01 5.542,1.594 false 6.375,0.208 6.823,0.208 false 6.385,0.615 6.802,0.615 false 3.094,0.958 3.375,1.313 0.281,0.354 18 false 4 6.021,1.854 6.302,2.208 0.281,0.354 18 false 3 4.958,2.302 5.271,2.5 0.313,0.198 10 false x2 2.958,0.49 3.271,0.688 0.313,0.198 10 false x2 6.208,0.031 6.49,0.385 0.281,0.354 18 false 1 6.198,0.448 6.479,0.802 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
4 CLUTCH PEDAL STROKE SENSOR ASSEMBLY 89280 (Click here) - -

CAUTION / NOTICE / HINT

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 89280 4.REMOVE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

a.
C459850N01
0.073,0.021 0.24,0.302 0.167,0.281 18 true i 3.823,0 3.958,0.302 0.135,0.302 18 true ii

i.

Disconnect the clutch pedal stroke sensor assembly connector.


ii.

Remove the 2 nuts and clutch pedal stroke sensor assembly from the clutch pedal support assembly.

NOTICE:
·

Do not drop the clutch pedal stroke sensor assembly.

·

If the clutch pedal stroke sensor assembly has been dropped, replace the clutch pedal stroke sensor assembly with a new one.