Home › Drivetrain › EC6D (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › from 2021.07
RM3700E _52 Drivetrain _104886 EC6D MANUAL TRANSMISSION / TRANSAXLE _0480439 MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

EC6D MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C462664N01
1.135,0.833 1.469,0.833 false 1.656,2.021 1.656,2.354 false 4.24,3.531 4.573,3.531 false 5.469,4.958 5.802,4.958 false 1.792,4.5 2.125,4.5 false 6.49,0.208 6.823,0.208 false 6.521,0.625 6.813,0.625 false 6.5,1.01 6.823,1.01 false 5.656,3.604 5.99,3.604 false 6,0.031 6.51,0.396 0.51,0.365 18 false 1, 2 1.583,1.156 1.896,1.354 0.313,0.198 10 false x2 5.156,3.448 5.469,3.646 0.313,0.198 10 false x2 3.156,5.427 3.469,5.625 0.313,0.198 10 false x4 3.406,5.313 3.719,5.51 0.313,0.198 10 false x4 3.833,5.25 4.146,5.448 0.313,0.198 10 false x9 6.302,0.448 6.583,0.802 0.281,0.354 18 false 3 5.281,4.792 5.563,5.146 0.281,0.354 18 false 4 1.583,4.323 1.865,4.677 0.281,0.354 18 false 5 4.052,3.354 4.333,3.708 0.281,0.354 18 false 6 1.604,2.354 1.885,2.708 0.281,0.354 18 false 7 6.052,3.438 6.333,3.792 0.281,0.354 18 false 8 1.542,0.667 1.823,1.021 0.281,0.354 18 false 9 6.177,0.844 6.583,1.198 0.406,0.354 18 false 10

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 FRONT WHEELS - - - -
5 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
6 ENGINE UNDER COVER LH 51442C - - -
7 ENGINE UNDER COVER RH 51441C - - -
8 FRONT FENDER LINER LH 53876A - - -
9 FRONT FENDER LINER RH 53875A - - -
10 DRAIN MANUAL TRANSAXLE OIL - - (Click here) -

C462666N02
0.083,0.083 7.083,2.917 7,2.833 0.083,2.917 7.083,5.75 7,2.833 3.479,0.479 3.813,0.479 false 4.333,0.802 4.667,0.802 false 6.146,1.885 6.479,1.885 false 5.906,4.667 6.24,4.667 false 4.844,4.125 5.177,4.125 false 3.375,3.292 3.708,3.292 false 4.49,2.469 4.823,2.469 false 4.479,5.354 4.813,5.354 false 0.167,0.177 0.542,0.417 0.375,0.24 12 false *A 0.167,3.01 0.542,3.25 0.375,0.24 12 false *B 2.292,3.552 2.75,3.75 0.458,0.198 10 false x12 2.271,0.688 2.729,0.885 0.458,0.198 10 false x11 4.875,2.292 5.427,2.646 0.552,0.354 18 false 15 5.229,3.958 5.781,4.313 0.552,0.354 18 false 14 3.854,0.292 4.406,0.646 0.552,0.354 18 false 12 6.281,4.49 6.833,4.844 0.552,0.354 18 false 13 3.76,3.115 4.313,3.469 0.552,0.354 18 false 11 4.865,5.177 5.417,5.531 0.552,0.354 18 false 15 4.708,0.625 5.26,0.979 0.552,0.354 18 false 14 6.521,1.708 7.073,2.063 0.552,0.354 18 false 11

Procedure Part Name Code
Z101186

Z101188

Z101187

11 WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY - - - -
12 WATER GUARD PLATE RH 55734A - - -
13 WATER GUARD PLATE LH 55735A - - -
14 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
15 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -

*A for LHD *B for RHD

C462667N02
4.198,0.823 4.531,0.823 false 2.458,1.792 2.792,1.792 false 0.854,2.365 1.188,2.365 false 5.333,2.135 5.667,2.135 false 3.865,0.656 4.417,1.01 0.552,0.354 18 false 18 5.719,1.958 6.271,2.313 0.552,0.354 18 false 19 5.698,1.365 6.104,1.656 0.406,0.292 10 false x3 4.635,0.333 5.042,0.625 0.406,0.292 10 false x2 2.135,1.615 2.688,1.969 0.552,0.354 18 false 17 0.521,2.198 1.073,2.552 0.552,0.354 18 false 16

Procedure Part Name Code
Z101186

Z101188

Z101187

16 AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE - - - -
17 AUXILIARY BATTERY 28800 - - -
18 ECM 89661 (Click here) - -
19 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -

C462668N01
5.583,0.417 7,1.333 1.417,0.917 4.167,0.417 5.583,1.333 1.417,0.917 1.583,3.917 1.583,3.583 false 2.99,5.375 3.323,5.375 false 6.521,0.219 6.854,0.219 false 6.281,0.938 6.615,0.938 false 5.792,2.875 6.125,2.875 false 5.156,1.958 5.49,1.958 false 4.833,1.688 5,1.51 5,1.51 5.167,1.51 false 2.302,5.448 2.635,5.448 false 4.813,0.938 5.146,0.938 false 2.24,0.813 2.573,0.813 false 2.635,0.625 3.188,0.979 0.552,0.354 18 false 22 5.198,0.771 5.552,1.094 0.354,0.323 18 false 25 5.552,1.792 5.865,2.135 0.313,0.344 18 false 20 3.594,5.198 3.906,5.542 0.313,0.344 18 false 23 6.188,0.042 6.656,0.396 0.469,0.354 18 false 24 6.427,2.698 6.74,3.042 0.313,0.344 18 false 26 6.656,0.771 7.031,1.115 0.375,0.344 18 false 25 1.458,3.917 2.01,4.271 0.552,0.354 18 false 21 5.219,1.417 5.406,1.604 0.188,0.188 10 false ● 4.594,1.438 4.823,1.646 0.229,0.208 10 false x2 4.896,1.625 5.125,1.833 0.229,0.208 10 false x2 4.229,0.469 4.604,0.708 0.375,0.24 12 false *A 5.646,0.458 6.021,0.698 0.375,0.24 12 false *B 2.156,5.344 2.344,5.531 0.188,0.188 10 false ● 1.26,2.51 1.49,2.719 0.229,0.208 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

20 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B - - -
21 NO. 3 WATER BY-PASS HOSE ASSEMBLY 16290F - - -
22 ENGINE WIRE 82121 - - -
23 CLUTCH HOSE 31418 (Click here) - -
24 SECURE STEERING WHEEL - (Click here) - -
25 COLUMN HOLE COVER SILENCER SHEET 45259A - - -
26 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -

*A for LHD *B for RHD
● Non-reusable part - -

C460750N04
1.104,1.594 1.406,1.594 false 5.865,0.427 6.167,0.427 false 3.323,3.583 3.75,3.583 false 1.813,4.052 2.271,4.052 false 3.813,2.417 3.813,1.99 false 2.719,2.406 2.417,2.406 false 5.885,1.5 6.198,1.698 0.313,0.198 10 false x2 5.708,1.927 6.021,2.125 0.313,0.198 10 false x2 2.021,2.51 2.333,2.708 0.313,0.198 10 false x2 2.438,2.885 2.75,3.083 0.313,0.198 10 false x2 0.969,1.479 1.125,1.677 0.156,0.198 10 false ● 6.219,0.313 6.375,0.51 0.156,0.198 10 false ● 3.865,2.385 4.417,2.74 0.552,0.354 18 false 30 2.969,3.417 3.521,3.771 0.552,0.354 18 false 28 1.51,3.885 2.063,4.24 0.552,0.354 18 false 27 4.094,4.094 4.406,4.292 0.313,0.198 10 false x2 2.563,4.396 2.875,4.594 0.313,0.198 10 false x4 2.792,2.24 3.344,2.594 0.552,0.354 18 false 29

Procedure Part Name Code
Z101186

Z101188

Z101187

27 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
28 CENTER NO. 1 FLOOR BRACE 57543C - - -
29 NO. 2 AIR FUEL RATIO SENSOR 89467C - - -
30 FRONT EXHAUST PIPE ASSEMBLY 17410 (Click here) - -

● Non-reusable part - -

C462671N01
0.167,1.031 2.583,2.448 2.417,1.417 0.167,2.448 2.583,3.865 2.417,1.417 1.052,0.625 1.802,0.792 0.75,0.167 5.344,0.813 6.094,0.979 0.75,0.167 1.396,3.073 1.063,3.073 false 1.385,1.719 1.052,1.719 false 3.344,2.271 3.01,2.271 false 4.844,0.563 4.552,0.563 false 2.688,0.323 2.427,0.323 false 6.813,0.292 6.479,0.292 false 6.188,4.188 5.854,4.188 false 4.896,2.198 4.896,2.531 false 4.885,3.208 4.719,3.208 4.719,3.208 4.469,4.063 true 6.083,1.698 5.75,1.698 false 3.042,4.49 2.76,4.49 false 2.135,0.719 1.802,0.719 false 5.344,0.896 5.01,0.896 false 6.146,1.521 6.531,1.906 0.385,0.385 18 false 39 4.771,2.521 5.167,2.906 0.396,0.385 18 false 33 5.156,0.396 5.573,0.74 0.417,0.344 18 false 34 2.448,4.323 2.927,4.698 0.479,0.375 18 false 38 5.208,3.021 5.688,3.365 0.479,0.344 18 false 36 5.875,4.573 6.188,4.771 0.313,0.198 10 false x2 5.031,0.917 5.344,1.115 0.313,0.198 10 false x2 0.75,1.542 1.229,1.885 0.479,0.344 18 false 32 6.448,4.01 6.76,4.344 0.313,0.333 18 false 37 0.75,2.896 1.229,3.24 0.479,0.344 18 false 32 2.083,0.146 2.5,0.49 0.417,0.344 18 false 34 2.25,0.719 2.563,0.917 0.313,0.198 10 false x2 0.25,1.115 0.625,1.354 0.375,0.24 12 false *A 0.25,2.542 0.625,2.781 0.375,0.24 12 false *B 5.792,1.333 6.104,1.531 0.313,0.198 10 false x2 5.49,4.969 5.802,5.167 0.313,0.198 10 false x2 5.073,5.292 5.385,5.49 0.313,0.198 10 false x2 4.208,5.469 4.521,5.667 0.313,0.198 10 false x2 3.917,5.135 4.229,5.333 0.313,0.198 10 false x2 3.146,4.781 3.458,4.979 0.313,0.198 10 false x4 6.135,0.125 6.615,0.469 0.479,0.344 18 false 35 3.396,2.094 3.792,2.479 0.396,0.385 18 false 31 5.417,0.823 6.188,1.031 0.771,0.208 8 false 43 (438, 32) 1.135,0.635 1.906,0.844 0.771,0.208 8 false 43 (438, 32)

Procedure Part Name Code
Z101186

Z101188

Z101187

31 FLYWHEEL HOUSING SIDE COVER 11363A - - -
32 STARTER ASSEMBLY 28100 - - -
33 FRONT DRIVE SHAFT ASSEMBLY - - - -
34 ENGINE HANGERS - (Click here) - -
35 ENGINE SUPPORT BRIDGE - (Click here) - -
36 ENGINE MOVING CONTROL ROD 12363A (Click here) - -
37 FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY 51201 (Click here) - -
38 NO. 2 ENGINE MOVING CONTROL ROD 12364B - - -
39 DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY 43409E - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

C462181N01
5.26,4.719 5.625,4.719 false 5.427,2.656 5.771,2.656 false 5.823,1.646 6.115,1.646 false 6.469,0.292 6.802,0.292 false 5.938,4.542 6.49,4.896 0.552,0.354 18 false 42 6.146,0.115 6.698,0.469 0.552,0.354 18 false 40 1.281,4.323 1.563,4.594 0.281,0.271 10 false x4 4.99,3.396 5.271,3.667 0.281,0.271 10 false x2 5.427,2.146 5.708,2.417 0.281,0.271 10 false x4 5.844,2.49 6.198,2.938 0.354,0.448 18 false 43 6.188,1.479 6.542,1.927 0.354,0.448 18 false 41 5.823,0.99 6.104,1.26 0.281,0.271 10 false x4 4.76,0.594 5.042,0.865 0.281,0.271 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

40 SUPPORT MANUAL TRANSAXLE ASSEMBLY 30300 (Click here) - -
41 ENGINE MOUNTING INSULATOR LH 12372A - - -
42 REMOVE MANUAL TRANSAXLE ASSEMBLY 30300 (Click here) - -
43 ENGINE MOUNTING BRACKET LH 12325A - - -

C465064N02
3.938,5.375 3.604,5.375 false 3.167,4.917 2.813,5.333 2.813,5.333 2.625,5.333 false 2.302,0.958 1.969,0.958 false 5.448,1.521 5.115,1.521 false 1.583,0.458 1.25,0.458 false 4.031,0.75 3.698,0.75 false 5.208,4.219 5.208,3.885 false 5.49,3.365 5.573,3.073 5.573,3.073 5.74,3.073 false 5.458,1.24 5.333,0.917 5.333,0.917 5.167,0.917 false 1.406,3.958 1.115,3.958 false 1.167,1.01 0.781,1.01 false 2.792,4.698 2.563,4.698 false 0.792,3.771 1.344,4.125 0.552,0.354 18 false 44 4.01,5.219 4.563,5.573 0.552,0.354 18 false 45 2.302,5.177 2.854,5.531 0.552,0.354 18 false 46 2.26,4.521 2.813,4.875 0.552,0.354 18 false 47 2.781,0.792 3.333,1.146 0.552,0.354 18 false 48 2.635,0.854 2.792,1.052 0.156,0.198 10 false ● 4.969,1.427 5.125,1.625 0.156,0.198 10 false ● 0.906,0.344 1.292,0.531 0.385,0.188 10 false ● ★ 1.74,0.375 2.052,0.573 0.313,0.198 10 false x3 3.354,4.375 3.667,4.573 0.313,0.198 10 false x2 3.375,0.583 3.927,0.938 0.552,0.354 18 false 50 5.073,4.208 5.625,4.563 0.552,0.354 18 false 51 5.813,2.896 6.365,3.25 0.552,0.354 18 false 51 4.854,0.729 5.406,1.083 0.552,0.354 18 false 52 0.458,0.833 1.01,1.188 0.552,0.354 18 false 49

Procedure Part Name Code
Z101186

Z101188

Z101187

44 CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE 31482 (Click here) - -
45 CLUTCH FLEXIBLE HOSE BRACKET 31484 - - -
46 CLUTCH RELEASE BLEEDER SUB-ASSEMBLY 31407B (Click here) - -
47 CLUTCH TUBE BOOT 31126B - - -
48 CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY 31400 (Click here) - -
49 BLEEDER CLUTCH RELEASE TUBE 31483 (Click here) - -
50 HEATER BRACKET 87121V - - -
51 WIRE HARNESS CLAMP BRACKET - - - -
52 TRANSMISSION CASE PLUG ASSEMBLY 35150D - - -

● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the manual transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the manual transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

Do not touch the engine, exhaust pipe or other high temperature components when they are hot.

·

Touching the engine, exhaust pipe or other high temperature components when they are hot could result in burns.



NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Z101186

Click here(Click here)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE FRONT WHEELS

Hide 51410 5.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 6.REMOVE ENGINE UNDER COVER LH

Hide 51441C 7.REMOVE ENGINE UNDER COVER RH

a.

Perform the same procedure as for the LH side.


Hide 53876A 8.SEPARATE FRONT FENDER LINER LH

Hide 53875A 9.SEPARATE FRONT FENDER LINER RH

a.

Perform the same procedure as for the LH side.


Hide 10.DRAIN MANUAL TRANSAXLE OIL

Hide 11.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55734A 12.REMOVE WATER GUARD PLATE RH (for LHD)

Hide 55735A 13.REMOVE WATER GUARD PLATE LH (for RHD)

Hide 16.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 28800 17.REMOVE AUXILIARY BATTERY

Hide 89661 18.REMOVE ECM

Z101186

Click here(Click here)

Hide 74404A 19.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 33820B 20.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C462646


Hide 31418 23.DISCONNECT CLUTCH HOSE

a.
C462648N01
3.281,1.344 3.458,1.625 0.177,0.281 18 true i 4,0.719 4.198,1 0.198,0.281 18 true ii

i.

Using a 10 mm union nut wrench, disconnect the clutch release cylinder to flexible hose tube from the clutch hose.


ii.

Remove the clip and disconnect the clutch hose from the clutch flexible hose bracket.



Hide 24.SECURE STEERING WHEEL

Z101186

Click here(Click here)

Hide 45259A 25.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 26.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Z101186

Click here(Click here)

Hide 51447D 27.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 57543C 28.REMOVE CENTER NO. 1 FLOOR BRACE

Hide 89467C 29.DISCONNECT NO. 2 AIR FUEL RATIO SENSOR

Hide 17410 30.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Z101186

Click here(Click here)

Hide 11363A 31.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 28100 32.REMOVE STARTER ASSEMBLY

Hide 34.INSTALL ENGINE HANGERS

Z101186

Click here(Click here)

Hide 35.INSTALL ENGINE SUPPORT BRIDGE

a.
C462654C01
5.313,0.802 5.313,0.583 5.313,0.583 5.063,0.583 true 5.125,0.948 4.802,0.948 true 1.99,0.875 2.281,0.448 2.281,0.448 2.448,0.448 true 2.458,0.333 2.656,0.542 0.198,0.208 10 true *a 4.635,0.844 4.813,1.031 0.177,0.188 10 true *b 4.885,0.479 5.073,0.677 0.188,0.198 10 true *c 0.365,0 0.51,0.292 0.146,0.292 18 false i
*a Existing Hole *b Protective Tape
*c Bolt - -


i.

Cover the existing holes in the left and right suspension tower with protective tape, then use a thin-bladed screwdriver to make holes in the tape, and insert the 2 bolts for setting the sub-beam of the engine support bridge.

Item Part No.
Bolt 9010-10226



b.
C462655C01
2.406,1.313 2.219,1.313 2.219,1.313 2.094,1.052 true 4.76,1.406 4.948,1.406 4.948,1.406 5.115,1.115 true 1.781,5.208 2.115,5.208 true 2.115,5.938 2.115,6.198 true 5.094,4.906 5.542,4.906 true 4.667,5.635 4.99,5.635 true 2.125,5.094 2.323,5.292 0.198,0.198 10 true *a 2.031,6.188 2.24,6.375 0.208,0.188 10 true *b 2.417,1.198 2.615,1.396 0.198,0.198 10 true *c 4.552,1.292 4.75,1.49 0.198,0.198 10 true *c 4.896,4.792 5.094,4.99 0.198,0.198 10 true *a 4.458,5.531 4.667,5.719 0.208,0.188 10 true *b 0.375,0.01 0.552,0.26 0.177,0.25 18 true i
*a Support Shaft *b Front Side Member
*c Bolt - -


i.

Install SST to the vehicle body as shown in the illustration.

SST
09940-10010  

CAUTION:
·
C330755C01
0.448,1.167 0.781,1.167 false 2.438,1.167 2.771,1.167 false 1.052,1.781 1.052,1.448 1.052,1.448 1.219,1.448 false 2.604,1.781 2.604,1.448 2.604,1.448 2.438,1.448 false 0.292,1.094 0.604,1.25 0.313,0.156 10 false *a 2.271,1.094 2.583,1.25 0.313,0.156 10 false *a 1.281,1.385 1.594,1.542 0.313,0.156 10 false *b 2.271,1.385 2.583,1.542 0.313,0.156 10 false *b
*a Support Shaft
*b Front Side Member


Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.

·

The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.



NOTICE:
·

Prevent SST from contacting the vehicle body exterior and windshield glass.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed before performing work.





c.
C462656C01
3.052,1.75 3.469,1.75 false 3.021,2 3.438,2 false 2.885,2.25 2.885,2.073 2.885,2.073 2.646,2.073 false 2.552,1.208 2.552,0.958 2.552,0.958 2.25,0.958 false 3.51,1.646 3.823,1.802 0.313,0.156 10 false *a 2.073,0.854 2.385,1.01 0.313,0.156 10 false *b 2.479,1.969 2.792,2.125 0.313,0.156 10 false *c 3.479,1.896 3.792,2.052 0.313,0.156 10 false *d 0.458,0.083 0.74,0.438 0.281,0.354 18 false i
*a Support Shaft *b Sub Beam
*c Front Side Member *d Threaded Portion


i.

Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.



d.
C462657C01
0.365,0.688 1.375,0.688 false 1.083,1.865 1.375,1.865 true 1.688,1.094 2.01,1.094 false 1.479,2 1.906,2 true 2.063,0.99 2.375,1.146 0.313,0.156 10 false *a 0.198,0.604 0.51,0.76 0.313,0.156 10 false *b 0.885,1.75 1.052,1.938 0.167,0.188 10 true *c 1.927,1.875 2.104,2.073 0.177,0.198 10 true *d 0.344,0 0.969,0.313 0.625,0.313 18 false i, ii
*a Chain Block Assembly *b Sling Bracket
*c Fuse Shackle *d Shackle (A)


i.

Install the chain block assembly to the sling bracket.


ii.

Install the division bar to the chain block assembly with the shackles.

CAUTION:
·
C338949C01
0.458,2.313 0.583,2.313 0.583,2.313 0.875,2.635 false 0.354,2.677 0.479,2.677 0.479,2.677 0.865,2.865 false 2.177,2.271 2.302,2.271 2.302,2.271 2.604,2.594 false 2.073,2.656 2.198,2.656 2.198,2.656 2.583,2.844 false 0.281,2.208 0.604,2.469 0.323,0.26 10 false *a 0.167,2.573 0.51,2.844 0.344,0.271 10 false *b 1.99,2.156 2.313,2.417 0.323,0.26 10 false *a 1.885,2.542 2.229,2.813 0.344,0.271 10 false *b
*a Fuse Shackle
*b Shackle (A)


Make sure the fuse shackle is on the chain block assembly side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·

If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with manual transaxle assembly may fall.

·
C330757C02
2.75,1 3.083,1 false 1.01,1 1.344,1 false 0.833,1.448 0.875,1.604 0.875,1.604 1.354,1.604 true 2.563,1.427 2.646,1.594 2.646,1.594 3.094,1.594 true 1.396,0.917 1.708,1.073 0.313,0.156 10 false *a 1.396,1.5 1.708,1.656 0.313,0.156 10 false *b 3.125,0.917 3.354,1.083 0.229,0.167 10 false *a 3.125,1.49 3.344,1.656 0.219,0.167 10 false *b
*a Fuse Shackle
*b Fuse Bolt


Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.

·

If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.





e.
C462658C01
1.01,1.823 0.646,1.823 true 2.26,3.656 1.896,3.656 true 1.396,0.979 1.625,1.104 1.625,1.104 1.771,1.104 true 2.438,0.76 2.438,0.969 true 1.313,1.469 1.625,1.469 true 1.688,3.115 1.385,3.281 1.385,3.281 1.271,3.281 true 1.74,3.594 1.469,3.76 1.469,3.76 1.323,3.76 true 0.583,3.104 0.583,3.333 true 0.448,1.729 0.646,1.906 0.198,0.177 10 true *1 2.26,3.552 2.448,3.729 0.188,0.177 10 true *2 2.354,0.948 2.563,1.146 0.208,0.198 10 true *a 1.781,1 1.99,1.188 0.208,0.188 10 true *b 1.625,1.365 1.823,1.563 0.198,0.198 10 true *c 0.365,0 0.875,0.344 0.51,0.344 18 false i, ii 0.51,3.323 0.677,3.521 0.167,0.198 10 true *a 1.094,3.177 1.26,3.375 0.167,0.198 10 true *b 1.167,3.646 1.333,3.844 0.167,0.198 10 true *c
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Chain - -


i.

Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 1st link of the chain to the No. 1 engine hanger.



ii.

Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 2nd link of the chain to the No. 2 engine hanger.




f.
C462659C01
3.146,0.615 3.458,0.771 0.313,0.156 10 false *a 0.375,0.01 0.656,0.365 0.281,0.354 18 false i
*a 120 mm (4.72 in.) or more - -


i.

Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.

HINT:

If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.




g.
C462660C01
4.021,0.927 4.24,0.51 4.24,0.51 4.438,0.51 false 3.313,1.458 3.719,1.458 true 3.74,1.375 3.938,1.583 0.198,0.208 10 true *a 4.49,0.406 4.802,0.563 0.313,0.156 10 false *b 5.844,0.385 6.156,0.542 0.313,0.156 10 false *c 1.083,0.375 1.396,0.531 0.313,0.156 10 false *d 1.073,2.313 1.24,2.5 0.167,0.188 10 true *f 3.031,0.302 3.344,0.469 0.313,0.167 10 false *e 0.365,0 0.646,0.354 0.281,0.354 18 false i 5.854,2.323 6.021,2.51 0.167,0.188 10 true *f
*a Chain Block Assembly *b Main Beam
*c Dimension (A) *d Dimension (B)
*e Right to Left Adjustment *f Front to Rear Adjustment


i.

Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.

CAUTION:
·

To prevent the engine with manual transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.

·
C330750C03
1.792,1.75 2.063,1.333 2.063,1.333 2.208,1.333 false 0.354,2.552 0.885,2.552 true 2.938,2.583 3.115,2.771 3.115,2.771 3.198,2.771 true 2.25,1.24 2.563,1.396 0.313,0.156 10 false *a 0.188,2.458 0.417,2.656 0.229,0.198 10 false *b 0.396,1.323 0.708,1.479 0.313,0.156 10 false *d 3.083,1.333 3.396,1.49 0.313,0.156 10 false *c 3.24,2.677 3.417,2.875 0.177,0.198 10 false *b
*a Main Beam
*b Sub Beam
*c Dimension (A)
*d Dimension (B)


Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.

·

Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with manual transaxle assembly and engine support bridge to fall, possibly causing serious injury.



NOTICE:
·
C330751

Do not perform any procedures if the chain of the chain block assembly is not straight.

·

When removing the engine mount, if the chain of the chain block assembly is not straight, the engine assembly or transaxle assembly may contact the vehicle body.





h.
C462661C01
1.229,1.708 1.417,1.896 0.188,0.188 10 true *b 5.833,1.656 6.021,1.844 0.188,0.188 10 true *b 2.271,0.073 2.469,0.271 0.198,0.198 10 false *a 4.375,1.167 4.573,1.354 0.198,0.188 10 true *a 5.125,1.344 5.313,1.542 0.188,0.198 10 true *a 2.615,1.188 2.813,1.365 0.198,0.177 10 true *a 1.875,1.344 2.073,1.542 0.198,0.198 10 true *a 0.354,0.01 0.635,0.365 0.281,0.354 18 false i 4.729,0.073 4.927,0.271 0.198,0.198 10 false *a
*a Wing Bolt *b Bolt


i.

Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.

Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)

CAUTION:
·
C330761

Do not perform any procedures before tightening the bolts to the specified torque.

·

Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.





i.
C462662C01
4.25,2.177 4.458,2.375 0.208,0.198 10 true *a 0.365,0 0.646,0.354 0.281,0.354 18 false i
*a Turn - -


i.

Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C330770C01
2.99,2.292 3.302,2.448 0.313,0.156 10 false *a
*a 41 N*m (418 kgf*cm, 30 ft.*lbf) or more


·

When suspending the engine with manual transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.





Hide 12363A 36.DISCONNECT ENGINE MOVING CONTROL ROD

Z101186

Click here(Click here)

Hide 51201 37.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 12364B 38.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C462650


Hide 30300 40.SUPPORT MANUAL TRANSAXLE ASSEMBLY

a.
C462663C01
3.333,0.656 3.656,0.656 true 3.135,0.563 3.333,0.76 0.198,0.198 10 true *a 0.385,0 0.667,0.354 0.281,0.354 18 false i
*a Lashing Belt - -


i.

Using a transmission jack and lashing belt or rope, support the manual transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely support the manual transaxle assembly.

·

Using a lashing belt or a rope, secure the manual transaxle assembly to the transmission jack.





Hide 12372A 41.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C462652


Hide 30300 42.REMOVE MANUAL TRANSAXLE ASSEMBLY

Z101186

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the manual transaxle assembly and engine assembly.


HINT:
·

Bolt (A): Remove from the manual transaxle assembly side.

·

Bolt (B): Remove from the engine assembly side.




a.
C461197N03
4.052,0 4.208,0.198 0.156,0.198 10 false A 3.198,0 3.354,0.198 0.156,0.198 10 false A 4.219,1.583 4.396,1.771 0.177,0.188 10 false A 4.458,1.417 4.615,1.615 0.156,0.198 10 false B 2.781,0.677 2.938,0.875 0.156,0.198 10 false B 3.031,1.5 3.167,1.677 0.135,0.177 10 true B 3.219,1.604 3.354,1.781 0.135,0.177 10 true B


Hide 31482 44.REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

Z101186

Click here(Click here)

Hide 31407B 46.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 31126B 47.REMOVE CLUTCH TUBE BOOT

Hide 31400 48.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Z101186

Click here(Click here)

Hide 31483 49.REMOVE BLEEDER CLUTCH RELEASE TUBE

Z101186

Click here(Click here)