|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with a union nut wrench | ● | Non-reusable part |
|
Clutch spline grease |
|
Gear oil |
| ★ | Precoated part | - | - |
| *1 | MANUAL TRANSAXLE ASSEMBLY | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| *A | w/ Stop and Start System | *B | w/o Stop and Start System |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.
35150D
1.INSTALL TRANSMISSION CASE PLUG ASSEMBLY
|
Gear Oil | - | - |
Coat a new O-ring with gear oil and install it to the transmission case plug assembly.
Ensure that the O-ring is not twisted.
Install the transmission case plug assembly to the manual transaxle assembly.
Be careful not to damage the O-ring.
2.INSTALL WIRE HARNESS CLAMP BRACKET
87121V
3.INSTALL HEATER BRACKET
31126B
5.INSTALL CLUTCH TUBE BOOT
31484
13.INSTALL CLUTCH FLEXIBLE HOSE BRACKET
12325A
15.INSTALL ENGINE MOUNTING BRACKET LH
| *a | Temporarily Tighten | - | - |
Install the engine mounting bracket LH to the manual transaxle assembly with the 4 bolts in the order shown in the illustration.
12364B
16.INSTALL NO. 2 ENGINE MOVING CONTROL ROD
| *a | Temporarily Tighten | - | - |
Install the No. 2 engine moving control rod to the manual transaxle assembly with the 4 bolts in the order shown in the illustration.
51201
17.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
18.INSTALL ENGINE ASSEMBLY
| *1 | Knock Pin | - | - |
Check that the 2 knock pins are installed on the engine assembly before installing the manual transaxle assembly.
Align the input shaft with the clutch disc and install the engine assembly to the manual transaxle assembly.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not forcibly pry on the manual transaxle assembly when installing it to the engine assembly.
Do not apply excessive force to the manual transaxle assembly as this will break the input shaft.
Make sure that the knock pins fit securely into the holes when installing the manual transaxle assembly to the engine assembly.
Make sure that the contact surfaces of the engine assembly and manual transaxle assembly are flat against each other before tightening the bolts.
Temporarily install the bolt (A).
Bolt (A): Install from the manual transaxle assembly side.
Install the bolt (B), then fully tighten the bolt (A).
Bolt (B): Install from the manual transaxle assembly side.
Install the bolt (C).
Bolt (C): Install from the manual transaxle assembly side.
Install the 4 bolts (D).
Bolt (D): Install from the engine assembly side.
43409E
19.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
Install the drive shaft heat insulator sub-assembly to the manual transaxle assembly and engine assembly with the 2 bolts in the order shown in the illustration.
82121
20.CONNECT ENGINE WIRE
16290F
21.INSTALL NO. 3 WATER BY-PASS HOSE ASSEMBLY
28100
22.INSTALL STARTER ASSEMBLY
w/ Stop and Start System:
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>STARTER (w/ Stop And Start System)>INSTALLATION
w/o Stop and Start System:
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>STARTER (w/o Stop And Start System)>INSTALLATION
11363A
23.INSTALL FLYWHEEL HOUSING SIDE COVER
24.REMOVE ENGINE HANGERS
25.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE