Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0442086 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B232588  Door LIN Bus off  


DESCRIPTION

If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more, DTC B232588 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B232588 Door LIN Bus off The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Front power window regulator motor assembly (driver door)

·

Front power window regulator motor assembly (front passenger door)

·

Rear power window regulator motor assembly (rear RH door)

·

Rear power window regulator motor assembly (rear LH door)

·

Double lock door control relay assembly (w/ Double Locking System)

·

Wire harness or connector


Main Body A

WIRING DIAGRAM

C434542E04
0.146,0.083 0.854,0.292 0.708,0.208 12 false for RHD: 1.469,1.042 1.844,1.229 0.375,0.188 10 false LIN2 0.573,2.333 1.729,2.875 1.156,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 1.823,2.24 3.24,2.813 1.417,0.573 10 false Power Distribution Box Assembly 2.75,4.49 3.208,4.688 0.458,0.198 10 false MPX1 1.74,5.365 3.333,5.771 1.594,0.406 10 false Double Lock Door Control Relay Assembly *1 0.177,9.156 2.073,9.375 1.896,0.219 10 false *1: w/ Double Locking System 0.604,9.521 2.5,9.74 1.896,0.219 10 false : LIN Communication Line 5,1.052 5.375,1.24 0.375,0.188 10 false LIN1 5,1.406 5.375,1.594 0.375,0.188 10 false LIN2 4.99,2.885 5.365,3.073 0.375,0.188 10 false LIN 4.719,3.521 6.635,3.917 1.917,0.396 10 false Front Power Window Regulator Motor Assembly (Driver Door) 5,4.542 5.375,4.729 0.375,0.188 10 false LIN 4.469,5.188 6.76,5.563 2.292,0.375 10 false Front Power Window Regulator Motor Assembly (Front Passenger Door) 5,6.198 5.375,6.385 0.375,0.188 10 false LIN 4.521,6.844 6.792,7.229 2.271,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear RH Door) 5,7.865 5.375,8.052 0.375,0.188 10 false LIN 4.531,8.531 6.802,8.917 2.271,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear LH Door) 1.917,0.844 2.115,1.021 0.198,0.177 10 false 15 1.875,1.052 2.125,1.229 0.25,0.177 10 false MB 3.125,0.833 3.323,1.01 0.198,0.177 10 false 17 3.094,1.031 3.344,1.208 0.25,0.177 10 false 4E 3.135,1.365 3.333,1.542 0.198,0.177 10 false 37 3.094,1.563 3.344,1.74 0.25,0.177 10 false 4B 4.75,0.896 4.948,1.073 0.198,0.177 10 false 17 4.74,1.26 4.938,1.438 0.198,0.177 10 false 16 4.781,1.698 5.156,1.885 0.375,0.188 10 false K5 4.802,2.729 5,2.906 0.198,0.177 10 false 9 4.719,3.365 5.094,3.552 0.375,0.188 10 false K7 4.823,4.385 5.021,4.563 0.198,0.177 10 false 9 4.479,5 4.854,5.188 0.375,0.188 10 false L7 4.813,6.031 5.01,6.208 0.198,0.177 10 false 9 4.531,6.656 4.906,6.844 0.375,0.188 10 false M4 4.833,7.719 5.031,7.896 0.198,0.177 10 false 9 4.542,8.344 4.917,8.531 0.375,0.188 10 false N4 3.229,4.302 3.427,4.479 0.198,0.177 10 false 9 1.75,5.188 2.094,5.354 0.344,0.167 10 false H42 4.771,1.875 6.365,2.271 1.594,0.396 10 false Multiplex Network Master Switch Assembly

C434543E06
0.198,0.125 0.948,0.344 0.75,0.219 12 false for LHD: 1.51,1.031 1.885,1.219 0.375,0.188 10 false LIN2 1.969,0.854 2.208,1.021 0.24,0.167 10 false 15 0.698,2.333 1.865,2.875 1.167,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 1.948,2.271 3.354,2.677 1.406,0.406 10 false Power Distribution Box Assembly 5.052,1.052 5.427,1.24 0.375,0.188 10 false LIN1 5.052,1.406 5.427,1.594 0.375,0.188 10 false LIN2 4.875,1.927 6.458,2.313 1.583,0.385 10 false Multiplex Network Master Switch Assembly 5.052,2.896 5.427,3.083 0.375,0.188 10 false LIN 4.719,3.542 6.635,3.917 1.917,0.375 10 false Front Power Window Regulator Motor Assembly (Driver Door) 5.063,4.552 5.438,4.74 0.375,0.188 10 false LIN 4.49,5.198 6.781,5.583 2.292,0.385 10 false Front Power Window Regulator Motor Assembly (Front Passenger Door) 5.073,6.188 5.448,6.375 0.375,0.188 10 false LIN 4.531,6.865 6.823,7.25 2.292,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear RH Door) 5.052,7.854 5.427,8.042 0.375,0.188 10 false LIN 4.573,8.552 6.865,8.938 2.292,0.385 10 false Rear Power Window Regulator Motor Assembly (Rear LH Door) 0.625,9.521 2.281,9.719 1.656,0.198 10 false : LIN Communication Line 1.958,1.042 2.198,1.208 0.24,0.167 10 false MB 3.219,0.854 3.458,1.021 0.24,0.167 10 false 17 3.188,1.031 3.427,1.198 0.24,0.167 10 false 4E 4.802,0.885 5.042,1.052 0.24,0.167 10 false 17 4.792,1.25 5.031,1.417 0.24,0.167 10 false 16 4.875,1.74 5.167,1.906 0.292,0.167 10 false L13 4.875,2.729 5.115,2.896 0.24,0.167 10 false 9 4.719,3.375 5.094,3.563 0.375,0.188 10 false L7 4.875,4.396 5.115,4.563 0.24,0.167 10 false 9 4.49,5.021 4.865,5.208 0.375,0.188 10 false K7 4.854,6.01 5.094,6.177 0.24,0.167 10 false 9 4.542,6.677 4.917,6.865 0.375,0.188 10 false M4 4.854,7.698 5.094,7.865 0.24,0.167 10 false 9 4.583,8.385 4.958,8.573 0.375,0.188 10 false N4

CAUTION / NOTICE / HINT

NOTICE:
·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for RHD A
for LHD B



A

3.CHECK FOR DTC

B

20.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
B232588 is output A
B232588 is not output B



A

4.CLEAR DTC

B

4.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

5.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)
5.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

Pre-procedure1

a.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

6.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

6.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

7.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
7.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the K5 multiplex network master switch assembly connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

8.CLEAR DTC

B

19.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
8.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

9.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)
9.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

Pre-procedure1

a.

Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

10.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

10.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

11.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)
11.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

Pre-procedure1

a.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

12.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

12.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

13.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)
13.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

Pre-procedure1

a.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

14.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

14.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

15.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
15.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

Pre-procedure1

a.

Disconnect the H42 double lock door control relay assembly connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

16.CLEAR DTC

B

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

16.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

17.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
17.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

Pre-procedure1

a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

HINT:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL



b.

Reconnect the power distribution box assembly connector.


c.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


d.

Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.


e.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


f.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-15 (LIN2) - Body ground Always 10 kΩ or higher
MB-15 (LIN2) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

18.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
18.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

Pre-procedure1

a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


c.

Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.


d.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


e.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - Body ground Always 10 kΩ or higher
4E-17 - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))

Pre-procedure1

a.

Disconnect the K5 multiplex network master switch assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly (driver door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K5,K7)Location & Routing

Click Connector(K5)Body>Front Door Wire RH / Television Camera Wire>Multiplex Network Master Switch Assembly

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

K5-16 (LIN2) or K7-9 (LIN) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
B232588 is output A
B232588 is not output B



A

21.CLEAR DTC

B

21.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

22.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)
22.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

Pre-procedure1

a.

Disconnect the L7 front power window regulator motor assembly (driver door) connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

23.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)

23.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

24.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
24.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the L13 multiplex network master switch assembly connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

25.CLEAR DTC

B

34.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
25.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

26.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)
26.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

Pre-procedure1

a.

Disconnect the K7 front power window regulator motor assembly (front passenger door) connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

27.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)

27.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

28.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)
28.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

Pre-procedure1

a.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

29.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)

29.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

30.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)
30.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

Pre-procedure1

a.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


Procedure1

a.

After 10 seconds have elapsed, check if the DTC is output.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B232588 is output A
B232588 is not output B



Post-procedure1

a.

None



A

31.CLEAR DTC

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)

31.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

32.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
32.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

Pre-procedure1

a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

HINT:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL



b.

Reconnect the power distribution box assembly connector.


c.

Disconnect the L7 front power window regulator motor assembly (driver door) connector.


d.

Disconnect the K7 front power window regulator motor assembly (front passenger door) connector.


e.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


f.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-15 (LIN2) - Body ground Always 10 kΩ or higher
MB-15 (LIN2) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

33.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
33.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

Pre-procedure1

a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the L7 front power window regulator motor assembly (driver door) connector.


c.

Disconnect the K7 front power window regulator motor assembly (front passenger door) connector.


d.

Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.


e.

Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - Body ground Always 10 kΩ or higher
4E-17 - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))

Pre-procedure1

a.

Disconnect the L13 multiplex network master switch assembly connector.


b.

Disconnect the L7 front power window regulator motor assembly (driver door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L13,L7)Location & Routing

Click Connector(L13)Body>Front Door Wire LH / Television Camera Wire>Multiplex Network Master Switch Assembly

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

L13-16 (LIN2) or L7-9 (LIN) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR