Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID VEHICLE CONTROL ECU › from 2021.07
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441187 HYBRID VEHICLE CONTROL ECU A

HYBRID / BATTERY CONTROL  HYBRID VEHICLE CONTROL ECU  REMOVAL  


CAUTION / NOTICE / HINT

A496547N01
0.25,0.083 5.917,3.583 5.667,3.5 6.385,0.302 6.719,0.302 false 6.417,0.615 6.75,0.615 false 1.656,0.906 1.99,0.906 false 1.708,2.521 2.042,2.521 false 4.948,1.406 5.281,1.406 false 4.99,3.156 5.271,3.156 false 0.25,1.833 5.917,1.833 false 5.656,1.302 5.938,1.656 0.281,0.354 18 false 4 6.219,0.479 6.5,0.833 0.281,0.354 18 false 1 6.208,0.146 6.49,0.5 0.281,0.354 18 false 2 2.073,0.75 2.354,1.104 0.281,0.354 18 false 3 2.125,2.375 2.406,2.729 0.281,0.354 18 false 3 5.625,3.01 5.906,3.365 0.281,0.354 18 false 4 0.354,1.896 0.635,2.25 0.281,0.354 12 false *B 0.313,0.156 0.594,0.51 0.281,0.354 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU - - - -
4 HYBRID VEHICLE CONTROL ECU 89981 (Click here) - -

*A for LHD *B for RHD

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle control ECU removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Replacement of hybrid vehicle control ECU Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.
ECU security key
·

DTCs are stored

·

Vehicle control history (RoB) are stored


(Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

Hide 89981 4.REMOVE HYBRID VEHICLE CONTROL ECU

Z101186

NOTICE:
·

If the ECU integration box is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.




a.
A457833N01
2.021,0.146 2.302,0.5 0.281,0.354 18 false i