Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › INVERTER WITH CONVERTER › from 2021.07
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441188 INVERTER WITH CONVERTER A

HYBRID / BATTERY CONTROL  INVERTER WITH CONVERTER  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A461198N05
0.083,4.25 0.75,4.417 0.667,0.167 5.25,1.167 5.917,1.333 0.667,0.167 3.76,0.448 4.917,0.615 1.156,0.167 1.021,1.219 1.688,1.385 0.667,0.167 5.531,4.885 6.198,5.052 0.667,0.167 2.26,4.927 2.802,4.927 false 3.344,3.938 3.5,4.177 3.5,4.177 3.667,4.177 false 0.75,4.333 0.917,4.333 0.917,4.333 0.979,4.521 false 6.104,2.396 6.104,2.708 false 5.927,1.25 6.094,1.25 6.094,1.25 6.25,1.656 false 5.833,3.958 5.5,3.958 false 5.875,4.885 5.875,4.552 false 4.052,1.083 3.719,1.083 false 1.979,2.042 1.646,2.042 false 2.021,1.302 1.688,1.302 false 3.76,0.531 3.427,0.531 false 0.104,4.25 0.781,4.427 0.677,0.177 8 false 15 (153, 11) 1,4.594 1.25,4.844 0.25,0.25 10 false x2 3.177,4.813 3.427,5.146 0.25,0.333 18 false 2 4.063,4.042 4.313,4.375 0.25,0.333 18 false 4 6.167,2.75 6.417,3.083 0.25,0.333 18 false 3 6.177,1.76 6.427,2.01 0.25,0.25 10 false x2 5.865,3.823 6.115,4.156 0.25,0.333 18 false 1 4.083,0.948 4.333,1.281 0.25,0.333 18 false 1 1.479,1.906 1.729,2.24 0.25,0.333 18 false 1 1.063,1.219 1.729,1.375 0.667,0.156 8 false 10 (102, 7) 3.875,0.448 5.542,0.865 1.667,0.417 8 false 9.8 (100, 87 in.*lbf) 5.26,1.167 5.938,1.344 0.677,0.177 8 false 15 (153, 11) 5.594,4.885 6.26,5.042 0.667,0.156 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WIRE HARNESS CLAMP BRACKET - - - -
2 NO. 1 INVERTER BRACKET G9214 (Click here) - -
3 NO. 2 INVERTER BRACKET G9215 (Click here) - -
4 HYBRID MOTOR CONTROL INVERTER ASSEMBLY G9200 (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

A461931N05
5.833,4.25 6.833,4.417 1,0.167 5.792,4.208 6.875,4.458 1.083,0.25 4.125,5.25 5.125,5.417 1,0.167 6.167,4.583 7.083,4.75 0.917,0.167 4.667,3 5.667,3.167 1,0.167 3.583,2.917 4.25,3.083 0.667,0.167 0.25,2.75 1.25,2.917 1,0.167 3.25,5.417 3.917,5.583 0.667,0.167 4.896,0.563 5.563,0.729 0.667,0.167 0.979,0.313 1.646,0.479 0.667,0.167 1.667,1.75 2.333,1.917 0.667,0.167 1.583,1.167 2.25,1.333 0.667,0.167 4.583,2.688 5.25,2.854 0.667,0.167 4.604,1.073 5.104,1.073 false 1.74,2.125 2.073,2.125 false 5.729,3.708 6.063,3.708 false 4.635,4.344 4.792,4.188 4.792,4.188 4.958,4.188 false 5.833,4.333 5.667,4.333 5.667,4.333 5.042,4.688 false 4.917,2.354 4.917,2.688 false 5.542,5.521 5.375,5.521 5.375,5.521 5.323,5.292 false 5.917,5.115 6,4.667 6,4.667 6.167,4.667 false 5.969,3.26 5.833,3.083 5.833,3.083 5.667,3.083 false 4.531,3.5 4.417,3 4.417,3 4.25,3 false 2.406,3.167 2.688,2.865 2.688,2.865 2.896,2.865 false 1.25,2.833 1.583,2.833 false 1.802,4.24 1.99,4.24 1.99,4.24 2.094,4.604 false 2.208,4.865 2.427,5.063 2.427,5.063 2.427,5.229 false 3.25,5.5 3.083,5.5 3.083,5.5 2.906,4.823 false 4.552,0.646 4.885,0.646 false 1.646,0.396 1.979,0.396 false 2.333,1.833 2.5,1.833 2.5,1.833 2.75,1.625 false 2.26,1.25 2.427,1.25 2.427,1.25 2.604,1.469 false 4.635,4.917 4.635,5.25 false 5.458,0.938 6.01,1.292 0.552,0.354 18 false 10 2.167,1.979 2.719,2.333 0.552,0.354 18 false 11 6.094,3.573 6.427,3.927 0.333,0.354 18 false 12 5.281,4.063 5.615,4.417 0.333,0.354 18 false 6 5.052,4.729 5.385,5.083 0.333,0.354 10 false x6 4.719,4.875 5.052,5.229 0.333,0.354 10 false x4 5.917,5.229 6.167,5.417 0.25,0.188 10 false x2 5.875,5.396 6.208,5.75 0.333,0.354 18 false 7 4.698,3 5.708,3.177 1.01,0.177 8 false 8.0 (82, 71 in.*lbf) 4.635,3.531 4.885,3.719 0.25,0.188 10 false x5 3.604,2.917 4.292,3.094 0.688,0.177 8 false 25 (255, 18) 3.302,2.75 3.583,3.063 0.281,0.313 18 false 5 1.583,2.896 1.833,3.083 0.25,0.188 10 false x2 0.292,2.75 1.344,2.906 1.052,0.156 8 false 9.5 (97, 84 in.*lbf) 1.583,4.104 1.865,4.417 0.281,0.313 18 false 9 2.5,5.25 2.781,5.563 0.281,0.313 18 false 8 2.688,4.729 2.938,4.917 0.25,0.188 10 false x2 1.031,0.313 1.677,0.469 0.646,0.156 8 false 10 (102, 7) 2.427,1.448 2.677,1.635 0.25,0.188 10 false x2 1.635,1.167 2.281,1.323 0.646,0.156 8 false 10 (102, 7) 1.75,1.75 2.396,1.906 0.646,0.156 8 false 10 (102, 7) 4.938,0.563 5.583,0.719 0.646,0.156 8 false 10 (102, 7) 4.615,2.688 5.26,2.844 0.646,0.156 8 false 10 (102, 7) 6.188,4.583 7.156,4.75 0.969,0.167 8 false 8.0 (82, 71 in.*lbf) 5.854,4.25 6.865,4.427 1.01,0.177 8 false 8.0 (82, 71 in.*lbf) 4.167,5.25 5.177,5.427 1.01,0.177 8 false 8.0 (82, 71 in.*lbf) 3.281,5.417 3.969,5.594 0.688,0.177 8 false 25 (255, 18)

Procedure Part Name Code
Z101186

Z101188

Z101187

5 INVERTER PROTECTOR G921E (Click here) - -
6 MOTOR CABLE G1148 (Click here) - -
7 UPPER INVERTER COVER G9022A (Click here) - -
8 INLET NO. 1 INVERTER COOLING HOSE G922AA (Click here) - -
9 OUTLET NO. 1 INVERTER COOLING HOSE G922C (Click here) - -
10 ENGINE WIRE 82121 (Click here) - -
11 PURGE VALVE (PURGE VSV) 25860 - - -
12 WIRE HARNESS CLAMP BRACKET - - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque

A490434N01
0.063,0.104 2.26,4.021 2.198,3.917 1.49,0.448 2.156,0.615 0.667,0.167 0.771,2.74 1.438,2.906 0.667,0.167 4.75,0.958 5.75,1.125 1,0.167 4.708,0.917 5.792,1.167 1.083,0.25 6.052,1.094 7.052,1.26 1,0.167 6.01,1.052 7.094,1.302 1.083,0.25 4.458,0.604 5.458,0.771 1,0.167 1.01,5.552 2.01,5.719 1,0.167 0.063,2.031 2.26,2.031 false 0.979,0.875 1.323,0.521 1.323,0.521 1.49,0.521 false 0.344,2.427 0.604,2.813 0.604,2.813 0.771,2.813 false 0.5,0.51 0.719,0.51 false 1.167,2.5 1.385,2.5 false 1.75,1.094 1.75,1.281 false 0.792,1.469 0.792,1.656 false 0.771,3.333 0.771,3.521 false 1.74,3.104 1.74,3.25 false 1.49,4.958 1.802,4.958 false 2.479,3.052 2.51,3.448 2.51,3.448 2.677,3.448 false 3.906,2.271 4.073,2.271 false 4.167,1.844 4.667,1.844 false 3.323,0.719 3.688,0.719 false 5.781,1.51 5.885,1.177 5.885,1.177 6.052,1.177 false 2.875,2.229 4.281,0.688 4.281,0.688 4.448,0.688 false 4.521,1.25 4.583,1.042 4.583,1.042 4.75,1.042 false 0.729,4.854 0.844,5.625 0.844,5.625 1.01,5.625 false 6.26,2.25 6.469,2.25 false 0.615,1.667 1.167,2.021 0.552,0.354 18 false 13 1.563,1.281 2.115,1.635 0.552,0.354 18 false 14 0.198,0.344 0.75,0.698 0.552,0.354 18 false 16 1.552,0.448 2.313,0.708 0.76,0.26 8 false 12 (122, 9) 0.844,2.74 1.604,3 0.76,0.26 8 false 12 (122, 9) 1.396,2.323 1.948,2.677 0.552,0.354 18 false 16 1.563,3.25 2.115,3.604 0.552,0.354 18 false 15 0.583,3.542 1.135,3.896 0.552,0.354 18 false 13 1.073,0.823 1.625,1.177 0.552,0.354 10 false x12 0.406,2.292 0.958,2.646 0.552,0.354 10 false x11 4.615,1.281 5.167,1.635 0.552,0.354 10 false x2 5.885,1.542 6.438,1.896 0.552,0.354 10 false x2 3.708,0.531 4.26,0.885 0.552,0.354 18 false 17 3.865,1.688 4.417,2.042 0.552,0.354 18 false 18 3.573,2.104 4.125,2.458 0.552,0.354 18 false 20 3,3.271 3.552,3.625 0.552,0.354 18 false 21 1.854,4.802 2.406,5.156 0.552,0.354 18 false 22 1.052,5.552 2.281,5.771 1.229,0.219 8 false 3.0 (31, 27 in.*lbf) 0.083,0.135 0.635,0.49 0.552,0.354 12 false *A 0.094,2.052 0.646,2.406 0.552,0.354 12 false *B 6.115,1.094 7.094,1.26 0.979,0.167 8 false 8.0 (82, 71 in.*lbf) 4.5,0.604 5.479,0.771 0.979,0.167 8 false 8.0 (82, 71 in.*lbf) 4.802,0.958 5.781,1.125 0.979,0.167 8 false 8.0 (82, 71 in.*lbf) 6.75,2.083 7.135,2.406 0.385,0.323 18 false 19

Procedure Part Name Code
Z101186

Z101188

Z101187

13 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
14 WATER GUARD PLATE RH 55734A - - -
15 WATER GUARD PLATE LH 55735A - - -
16 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
17 WINDSHIELD WIPER MOTOR AND LINK - - - -
18 HV AIR CONDITIONING WIRE 821H2 (Click here) - -
19 HV FLOOR UNDER WIRE 821H1 (Click here) - -
20 ENGINE WIRE 82121 (Click here) - -
21 ECM 89661 (Click here) - -
22 AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE - - - -

*A for LHD *B for RHD
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque

A461932N11
6.385,0.208 6.76,0.208 false 6.375,0.802 6.75,0.802 false 1.552,1.271 1.927,1.271 false 5.656,0.063 6.604,0.552 0.948,0.49 18 false 25, 26 1.24,1.115 2.188,1.604 0.948,0.49 18 false 23 6.073,0.656 6.583,1.052 0.51,0.396 18 false 24

Procedure Part Name Code
Z101186

Z101188

Z101187

23 SERVICE PLUG GRIP G3834 - - -
24 COOLANT (for Inverter) - - (Click here) -
25 COOLANT LEAK (for Inverter) - (Click here) - -
26 PERFORM RESOLVER LEARNING - (Click here) - -

PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.
A461161N01
1.844,0.375 2,0.573 0.156,0.198 10 true A 5.177,0.948 5.333,1.146 0.156,0.198 10 true A 6.135,1.104 6.292,1.302 0.156,0.198 10 true B

Torque:
Bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt B : 9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide G9214 2.INSTALL NO. 1 INVERTER BRACKET

a.
A461477N04
5.948,1.396 6.104,1.594 0.156,0.198 10 true A 5.51,1.406 5.667,1.604 0.156,0.198 10 true B 4.729,1.396 4.885,1.594 0.156,0.198 10 true B 0.531,0.156 0.719,0.469 0.188,0.313 18 true i 6.177,1.417 6.385,1.729 0.208,0.313 18 true ii 2.167,2.073 2.573,2.396 0.406,0.323 18 false iv 5.052,1.5 5.302,1.802 0.25,0.302 18 true iii

i.

Temporarily install the No. 1 inverter bracket to the hybrid vehicle transaxle assembly with the bolt and 2 nuts.

NOTICE:

Make sure that the hybrid motor control inverter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket.


HINT:

If the bolts and nuts are not tightened appropriately, the hybrid motor control inverter assembly may make an abnormal noise.



ii.

Fully tighten the bolt (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


iii.

Fully tighten the 2 nuts (B).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


iv.

Set the hybrid motor control inverter assembly on hybrid vehicle transaxle assembly.

NOTICE:
·

When installing the hybrid motor control inverter assembly, be careful not to damage the parts around it.

·

To prevent damage, do not hold the hybrid motor control inverter assembly by the connectors, brackets or cooling pipes.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·
A406201C03
0.625,2.229 0.802,2.427 0.177,0.198 10 true *a 0.625,3.365 0.813,3.542 0.188,0.177 10 true *b
*a Correct
*b Incorrect


Make sure that the hybrid motor control inverter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket



HINT:

If the bolts and nuts are not tightened appropriately, the hybrid motor control inverter assembly may make an abnormal noise.




Hide G9215 3.INSTALL NO. 2 INVERTER BRACKET

a.
A461165N01
0.656,0.042 0.844,0.333 0.188,0.292 18 true i 4.354,1.49 4.521,1.677 0.167,0.188 10 true A 5.156,1.521 5.323,1.708 0.167,0.188 10 true B 5.438,1.521 5.604,1.708 0.167,0.188 10 true B 5.729,1.51 5.896,1.698 0.167,0.188 10 true B 5.344,0.76 5.594,1.042 0.25,0.281 18 true iii 4.563,0.75 4.781,1.031 0.219,0.281 18 true ii

i.

Temporarily install the No. 2 inverter bracket to the hybrid vehicle transaxle assembly with the 4 bolts.


ii.

Fully tighten the bolt (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


iii.

Fully tighten the 3 bolts (B).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)



Hide G9200 4.INSTALL HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Z101186

CAUTION:

Wear insulated gloves.



a.
A461162N03
1.25,0.104 1.531,0.458 0.281,0.354 18 false i 1.521,2.156 1.708,2.438 0.188,0.281 18 true ii 1.604,3.146 1.792,3.365 0.188,0.219 10 false 1 2.979,3.104 3.167,3.323 0.188,0.219 10 false 2 4.771,3.51 4.927,3.688 0.156,0.177 10 true 2 3.51,3.521 3.667,3.698 0.156,0.177 10 true 1 3.5,2.969 3.792,3.25 0.292,0.281 18 true iii

i.

Temporarily install the hybrid motor control inverter assembly with the 4 bolts.


ii.

Fully tighten the 2 bolts in the order shown in the illustration to the hybrid motor control inverter assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


iii.

Fully tighten the 2 bolts in the order shown in the illustration to the hybrid motor control inverter assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)



Hide G921E 5.INSTALL INVERTER PROTECTOR

a.
A461163N01
1.406,0.052 1.688,0.406 0.281,0.354 18 false i 4.375,0.042 4.656,0.396 0.281,0.354 18 false ii 5.823,1.5 5.958,1.698 0.135,0.198 10 false 1 4.469,0.385 4.604,0.583 0.135,0.198 10 false 2

i.

Temporarily install the inverter protector with the 2 bolts.


ii.

Fully tighten the 2 bolts in the order shown in the illustration to the hybrid motor control inverter assembly.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)



Hide G1148 6.CONNECT MOTOR CABLE

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the hybrid motor control inverter assembly.



a.
A461468C01
1.802,0.448 1.469,0.219 true 1.25,0.146 1.5,0.313 0.25,0.167 10 false *a 6.49,1.531 6.677,1.719 0.188,0.188 10 true A 4.5,2.365 4.688,2.552 0.188,0.188 10 true 1 4.073,1.479 4.26,1.667 0.188,0.188 10 true 2 6.135,2.021 6.323,2.208 0.188,0.188 10 true 3 0.479,0.115 0.719,0.396 0.24,0.281 18 false i 4.052,0.885 4.313,1.188 0.26,0.302 18 true iii 6.656,1.167 6.844,1.448 0.188,0.281 18 true ii
*a Waterproof Seal - -


i.

Temporarily connect the motor cable to the hybrid motor control inverter assembly with the 4 bolts.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or hybrid motor control inverter assembly during disconnection.




ii.

Fully tighten the bolt (A).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iii.

Fully tighten the 3 bolts in the order shown in the illustration to connect the motor cable to the hybrid motor control inverter assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.
A461469N01
0.677,0.094 0.854,0.375 0.177,0.281 18 true i 3.99,0.052 4.167,0.333 0.177,0.281 18 true ii

i.

Temporarily install the 6 bolts.

NOTICE:
·

To prevent the threads from being damaged, temporarily tighten the 6 bolts by hand.

·

Do not damage the terminals, connector housing or hybrid motor control inverter assembly during disconnection.




ii.

Using an insulated tool, fully tighten the 6 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or hybrid motor control inverter assembly during disconnection.

·

Be sure to use a torque wrench to tighten the bolts.





Hide G9022A 7.INSTALL UPPER INVERTER COVER

Z101186

CAUTION:

Wear insulated gloves.



a.

Install the upper inverter cover to the hybrid motor control inverter assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Visually confirm that the inverter cover waterproof seal is securely installed before installing the upper inverter cover.

·

Do not touch the waterproof seal of the upper inverter cover.

·

Make sure that the interlock is fully engaged.

·

Do not damage the terminals, interlock connector or hybrid motor control inverter assembly during installation.

·

Do not allow any foreign matter or water to enter the hybrid motor control inverter assembly.

·
A464129C02
2.083,2.146 2.656,1.635 2.656,1.635 2,1.458 false 1.031,0.313 1.302,0.313 1.302,0.313 1.781,0.917 true 0.854,0.188 1.167,0.385 0.313,0.198 10 false *a 2.698,1.521 3.01,1.719 0.313,0.198 10 false *1
*1 Inverter Cover
*a Screw


Do not remove or excessively tighten the screw of the upper inverter cover.

·

Although the upper inverter cover may feel loose, this is not due to a malfunction.

·
A459828C01
1.521,1.719 1.74,1.896 0.219,0.177 10 true *a
*a No Gap


Push in the upper inverter cover until it contacts the hybrid motor control inverter assembly.




Hide G922AA 8.CONNECT INLET NO. 1 INVERTER COOLING HOSE

a.
A461470C01
3.24,0.729 3.042,0.385 true 2.792,0.729 2.594,0.385 true 2.448,0.229 2.76,0.385 0.313,0.156 10 false *a 2.885,0.24 3.198,0.396 0.313,0.156 10 false *b 3.042,1.208 3.354,1.365 0.313,0.156 10 false *c 4.031,0.052 4.344,0.208 0.313,0.156 10 false *d 4.635,0.688 4.948,0.844 0.313,0.156 10 false *e 4.323,0.208 4.677,0.385 0.354,0.177 10 false 120° 1.938,0.115 2.177,0.438 0.24,0.323 18 false i
*a Alignment Mark (Green) *b Rib
*c 2 to 5 mm (0.0787 to 0.197 in.) *d Up
*e LH Side - -


i.

Connect the inlet No. 1 inverter cooling hose to the hybrid motor control inverter assembly and slide the clip to secure it.

NOTICE:

To prevent foreign matter from entering the hybrid motor control inverter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.


HINT:
·

Make sure that the clip is positioned as shown in the illustration.

·

Make sure to align the alignment mark of the hose with the rib of the hybrid motor control inverter assembly.





Hide G922C 9.CONNECT OUTLET NO. 1 INVERTER COOLING HOSE

a.
A461471C01
3.24,0.729 3.042,0.385 true 2.792,0.729 2.594,0.385 true 2.448,0.229 2.76,0.385 0.313,0.156 10 false *a 2.885,0.24 3.198,0.396 0.313,0.156 10 false *b 3.042,1.208 3.354,1.365 0.313,0.156 10 false *c 4.031,0.052 4.344,0.208 0.313,0.156 10 false *d 4.635,0.688 4.948,0.844 0.313,0.156 10 false *e 4.323,0.208 4.708,0.427 0.385,0.219 10 false 120° 1.969,0.135 2.25,0.49 0.281,0.354 18 false i
*a Alignment Mark (Blue) *b Rib
*c 2 to 5 mm (0.0787 to 0.197 in.) *d Up
*e LH Side - -


i.

Connect the outlet No. 1 inverter cooling hose to the hybrid motor control inverter assembly and slide the clip to secure it.

NOTICE:

To prevent foreign matter from entering the hybrid motor control inverter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.


HINT:
·

Make sure that the clip is positioned as shown in the illustration.

·

Make sure to align the alignment mark of the hose with the rib of the hybrid motor control inverter assembly.





Hide 82121 10.INSTALL ENGINE WIRE

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:
·

To prevent the threads from being damaged, temporarily tighten the nut by hand.

·

Do not touch the waterproof seal or terminals of the connectors.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or hybrid motor control inverter assembly when connecting the connectors.




Torque:
10 N*m (102 kgf*cm, 89 in.*lbf)

Hide 25860 11.INSTALL PURGE VALVE (PURGE VSV)

Hide 12.INSTALL WIRE HARNESS CLAMP BRACKET

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

Hide 55734A 14.INSTALL WATER GUARD PLATE RH (for LHD)

Hide 55735A 15.INSTALL WATER GUARD PLATE LH (for RHD)

Hide 17.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 821H2 18.CONNECT HV AIR CONDITIONING WIRE

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:
·

Do not allow any foreign matter or water to enter the hybrid motor control inverter assembly.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or hybrid motor control inverter assembly when connecting the connector.




Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

Hide 821H1 19.CONNECT FLOOR UNDER WIRE

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:
·

Do not allow any foreign matter or water to enter the hybrid motor control inverter assembly.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or hybrid motor control inverter assembly when connecting the connector.




Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

Hide 82121 20.CONNECT ENGINE WIRE

Z101186

CAUTION:

Wear insulated gloves.


NOTICE:
·

Do not allow any foreign matter or water to enter the hybrid motor control inverter assembly.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or hybrid motor control inverter assembly when connecting the connectors.

·

Do not touch the waterproof seal or terminals of the connectors.




Hide 22.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Z101186

NOTICE:

Align the cutout of the air cleaner hose assembly with the protrusion of the throttle body with motor assembly.



Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)

Hide 24.ADD COOLANT (for Inverter)