Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for HV Model TMMF Made RHD) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0480781 BRAKE ACTUATOR(for HV Model TMMF Made RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for HV Model TMMF Made RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456276N01
3.073,0.938 3.406,0.938 false 4.156,1.302 4.49,1.302 false 5.292,1.917 5.625,1.917 false 4.521,3.365 4.854,3.365 false 6.396,0.323 6.729,0.323 false 6.375,0.75 6.708,0.75 false 6.406,1.115 6.74,1.115 false 6.167,0.146 6.448,0.5 0.281,0.354 18 false 1 6.156,0.563 6.438,0.917 0.281,0.354 18 false 2 6.188,0.958 6.469,1.313 0.281,0.354 18 false 7 5.75,1.75 6.031,2.104 0.281,0.354 18 false 5 4.583,1.083 4.865,1.438 0.281,0.354 18 false 4 3.5,0.729 3.781,1.083 0.281,0.354 18 false 3 4.969,3.167 5.25,3.521 0.281,0.354 18 false 6 2.271,1.333 2.729,1.531 0.458,0.198 10 false x12

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 WINDSHIELD WIPER MOTOR AND LINK - - - -
4 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
5 WATER GUARD PLATE LH 55735A - - -
6 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
7 DRAIN BRAKE FLUID - - - (Click here)

C456277N03
1.583,1.146 2,1.146 false 1.5,2.167 1.75,2.167 false 3.833,0.354 4.833,0.354 false 4.094,0.604 4.094,0.354 false 4.833,1.25 5,1.083 5,1.083 5.49,1.083 true 5.083,1.083 4.917,1.271 true 5.167,1.083 4.969,1.302 true 5.25,1.083 5.021,1.344 true 5.167,2.167 5.417,2.167 false 2.438,1.625 3.333,1.625 3.333,1.625 3.583,1.948 true 3.26,1.635 3.458,1.906 true 1.385,0.958 1.667,1.313 0.281,0.354 18 false 9 2.01,2.021 2.292,2.375 0.281,0.354 18 false 8 2.094,1.51 2.677,1.844 0.583,0.333 18 false 11 3.479,0.208 4.063,0.542 0.583,0.333 18 false 10 5.75,2.042 6.333,2.375 0.583,0.333 18 false 12 3.302,0.24 3.458,0.438 0.156,0.198 10 false ● 3.99,2.927 4.323,3.125 0.333,0.198 10 false x2 5.76,0.927 6.344,1.26 0.583,0.333 18 false 11

Procedure Part Name Code
Z101186

Z101188

Z101187

8 FLOOR UNDER WIRE 821H1 (Click here) - -
9 ENGINE ROOM MAIN WIRE - (Click here) - -
10 NO. 4 BRAKE TUBE CLAMP 47374B - - -
11 BRAKE LINE - (Click here) - -
12 BRAKE ACTUATOR WITH BRACKET - (Click here) - -

● Non-reusable part - -

C456278N01
2.677,1.188 3.094,1.188 false 2.833,3.344 3.25,3.344 false 4.073,2.052 4.156,1.635 4.156,1.635 4.323,1.635 false 4.573,4.75 3.323,4.75 3.323,4.75 3.323,4.583 true 3.729,4.583 3.729,4.75 false 4.063,4.573 4.063,4.74 false 4.583,5.156 3.333,5.156 3.333,5.156 3.333,4.99 true 3.708,4.99 3.708,5.156 false 4.052,4.99 4.052,5.156 false 2.313,1.063 2.865,1.417 0.552,0.354 18 false 14 2.469,3.198 3.021,3.552 0.552,0.354 18 false 13 4.635,4.594 5.188,4.948 0.552,0.354 18 false 16 4.667,5.021 5.219,5.375 0.552,0.354 18 false 15 4.385,1.542 4.698,1.74 0.313,0.198 10 false *1 4.958,2.219 5.271,2.417 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

13 NO. 1 BRAKE ACTUATOR BRACKET 44591 (Click here) - -
14 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -
15 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A - - -
16 BRAKE ACTUATOR BRACKET CUSHION 44547B - - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Skid control ECU (brake actuator assembly)
1.

Bleed air

2.

Perform "Reset Memory"

3.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned to ON (Click here)

CAUTION:
·
A340386

This vehicle contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed. Therefore, when servicing the brake system components, do not operate the brake pedal while the auxiliary battery is connected.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55815E 4.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 7.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 821H1 8.SEPARATE FLOOR UNDER WIRE

Z101186

CAUTION:

Be sure to wear insulated gloves.



a.
C456267


Hide 9.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C456268C01
1.865,0.052 2.146,0.406 0.281,0.354 18 false i
V113147

Release the lock lever
V113148

Disconnect the connector


i.

Release the lock lever and disconnect the connector from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




Hide 47374B 10.REMOVE NO. 4 BRAKE TUBE CLAMP

a.
C456269


Hide 11.SEPARATE BRAKE LINE

a.
C456270C01
1.823,1.521 2.406,1.354 true 2.729,1.063 3.167,1.021 true 1.552,1.198 2.135,1.156 true 1.615,0.958 2.281,1.021 true 1.563,0.698 2.438,0.906 true 2.656,0.792 3.01,0.573 true 3.208,0.917 3.417,1.135 0.208,0.219 10 true *a 3.99,0.063 4.26,0.406 0.271,0.344 18 false ii 1.594,1.448 1.802,1.667 0.208,0.219 10 true *b 3.042,0.448 3.25,0.667 0.208,0.219 10 true *f 1.323,0.542 1.531,0.76 0.208,0.219 10 true *e 1.375,0.833 1.583,1.052 0.208,0.219 10 true *d 1.292,1.115 1.5,1.333 0.208,0.219 10 true *c 0.344,0.073 0.615,0.417 0.271,0.344 18 false i
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH *d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH *f To Front Wheel Cylinder Assembly RH


i.

Use tags or make a memo to identify the places to reconnect the brake lines.


ii.

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.



Hide 12.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C456271N01
0.229,0.021 1.604,0.375 1.375,0.354 18 false i, ii 3.99,0.052 4.458,0.438 0.469,0.385 18 false iii

i.

Disconnect the connector.


ii.

Disengage the clamp to separate the wire harness from the No. 1 brake actuator bracket.


iii.

Remove the bolt, 2 nuts and brake actuator with bracket from the vehicle body.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.




Hide 44591 13.REMOVE NO. 1 BRAKE ACTUATOR BRACKET

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C456272


Hide 44510 14.REMOVE BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C456273


Hide 44521A 15.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

a.
C456274


Hide 44547B 16.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.
C456275