| *1 | BRAKE ACTUATOR BRACKET ASSEMBLY | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 5 | BRAKE ACTUATOR WITH BRACKET | - | ( )
|
- | - |
| 6 | INSTALL BRAKE LINE | - | ( )
|
- | - |
| 7 | NO. 4 BRAKE TUBE CLAMP | 47374B | - | - | - |
| 8 | ENGINE ROOM MAIN WIRE | - | ( )
|
- | - |
| 9 | FLOOR UNDER WIRE | 821H1 | ( )
|
- | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | * | For use with a union nut wrench or SST |
| ● | Non-reusable part | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
44547B
1.INSTALL BRAKE ACTUATOR BRACKET CUSHION
44521A
2.INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR
|
|
44510
3.INSTALL BRAKE ACTUATOR ASSEMBLY
|
|
Temporarily install the brake actuator assembly with the 3 bolts.
Fully tighten the 3 bolts in the order shown in the illustration.
44591
4.INSTALL NO. 1 BRAKE ACTUATOR BRACKET
|
|
5.INSTALL BRAKE ACTUATOR WITH BRACKET
Temporarily install the brake actuator with bracket to the vehicle body with the bolt and 2 nuts.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Be careful not to allow any brake fluid to enter the connector.
Do not hold the brake actuator assembly by the connector.
Do not drop the brake actuator with bracket when carrying it.
Install the brake actuator with bracket while avoiding the brake lines.
| *a | Torque Wrench Fulcrum Length | - | - |
Tighten the bolt.
Using SST, tighten the nut.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
8.5 N*m (87 kgf*cm, 75 in.*lbf)
Using SST, tighten the nut.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
8.5 N*m (87 kgf*cm, 75 in.*lbf)
Engage the clamp to install the wire harness to the No. 1 brake actuator bracket.
Connect the connector.
6.INSTALL BRAKE LINE
| *a | From 1st Chamber of Brake Booster with Master Cylinder Assembly | *b | From 2nd Chamber of Brake Booster with Master Cylinder Assembly |
| *c | To Front Wheel Cylinder Assembly LH | *d | To Rear Wheel Cylinder Assembly RH |
| *e | To Rear Wheel Cylinder Assembly LH | *f | To Front Wheel Cylinder Assembly RH |
| *g | Torque Wrench Fulcrum Length | - | - |
Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.
Using a union nut wrench, fully tighten the 6 brake lines.
Do not kink or damage the brake lines.
Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
(A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
(B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)
47374B
7.INSTALL NO. 4 BRAKE TUBE CLAMP
8.CONNECT ENGINE ROOM MAIN WIRE
|
Connect the connector |
|
Lock the lock lever |
Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.
Make sure that the connector is locked securely.
Make sure that the connector can be connected smoothly.
Do not allow water, oil or dirt to enter.
821H1
9.INSTALL FLOOR UNDER WIRE
|
|
55701J
10.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
55735A
11.INSTALL WATER GUARD PLATE LH
55815E
12.INSTALL FRONT NO. 1 VENTILATOR SEAL
13.INSTALL WINDSHIELD WIPER MOTOR AND LINK
14.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
15. UPDATE ECU SECURITY KEY
16.BLEED BRAKE LINE
17.PERFORM INITIALIZATION AND CALIBRATION
18.PERFORM TEST MODE INSPECTION
19.INSPECT BRAKE ACTUATOR USING GTS
20. CHECK AND CLEAR DTCS
21.PERFORM INITIALIZATION
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMMF Made)>PRECAUTION
The parking brake indicator light blinks (red) when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.
22. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART