Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for HV Model TMMF Made RHD) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0480809 BRAKE PEDAL STROKE SENSOR(for HV Model TMMF Made RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for HV Model TMMF Made RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C460889N01
5.365,2.458 6.448,2.625 1.083,0.167 5.323,2.417 6.49,2.667 1.167,0.25 3.354,0.76 3.688,0.76 false 4.198,2.99 4.635,2.99 false 6.396,0.667 6.729,0.667 false 6.469,0.208 6.802,0.208 false 6.417,1.177 6.75,1.177 false 5.031,2.542 5.365,2.542 false 5.948,0.042 6.594,0.396 0.646,0.354 18 false 1, 6 5.01,2.885 5.292,3.24 0.281,0.354 18 false 2 6.219,1.042 6.5,1.396 0.281,0.354 18 false 3 3.792,0.615 4.073,0.969 0.281,0.354 18 false 4 1.906,1.948 2.188,2.146 0.281,0.198 10 false x2 4.99,2.604 5.271,2.802 0.281,0.198 10 false x2 5.927,0.521 6.573,0.875 0.646,0.354 18 false 5, 7 5.448,2.458 6.49,2.667 1.042,0.208 8 false 8.5 (87, 75 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSPECT AND ADJUST BRAKE PEDAL HEIGHT - (Click here) - -
2 BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D (Click here) - -
3 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
5 PERFORM CALIBRATION - - - (Click here)
6 CHECK AND CLEAR DTC - (Click here) - -
7 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) - -

PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

Hide 89510D 2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
C436321C01
0.5,2.042 0.667,2.042 0.667,2.042 0.896,1.938 false 0.333,1.958 0.646,2.156 0.313,0.198 10 false *a
*a Locking Plate


When installing a new brake pedal stroke sensor assembly:

Until the brake pedal stroke sensor assembly has been installed to the brake pedal support assembly with the nut, do not press in the brake pedal stroke sensor lever locking plate.


HINT:

When the brake pedal stroke sensor assembly has been tightened to the specified torque, the locking plate will be released.


a.
C460888C01
1.844,0.292 2.083,0.573 true 1.813,0.823 2.063,0.771 true 1.563,0.146 1.802,0.344 0.24,0.198 10 true *a 1.552,0.75 1.76,0.948 0.208,0.198 10 true *b 0.417,0.052 0.698,0.406 0.281,0.354 18 false i 3.938,0.521 4.219,0.875 0.281,0.354 18 false ii
*a Brake Pedal Stroke Sensor Assembly Lever *b Brake Pedal Groove


i.

Install brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.




ii.

Connect the connector.



Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55606 4.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 7. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART