Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for HV Model TMC Made RHD) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0480816 BRAKE PEDAL STROKE SENSOR(for HV Model TMC Made RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for HV Model TMC Made RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442428N01
2.823,0.688 3.156,0.688 false 6.156,1.906 6.49,1.906 false 6.417,0.781 6.75,0.781 false 6.458,0.281 6.792,0.281 false 3.479,0.563 3.729,0.927 0.25,0.365 18 false 4 2.25,1.646 2.573,1.896 0.323,0.25 10 false x2 4.875,3.125 5.198,3.375 0.323,0.25 10 false x2 6.531,1.771 6.781,2.135 0.25,0.365 18 false 3 6.177,0.156 6.427,0.521 0.25,0.365 18 false 1 6.198,0.604 6.448,0.969 0.25,0.365 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
4 NO. 1 AIR DUCT 87211 (Click here) - -

C442429N01
4.219,1.271 4.406,1.458 4.406,1.458 4.573,1.458 false 4.896,1.323 5.177,1.677 0.281,0.354 18 false 5 4.875,0.844 5.177,1.052 0.302,0.208 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

5 BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal stroke sensor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Brake pedal stroke sensor assembly
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 87211 4.REMOVE NO. 1 AIR DUCT

Z101186

Click here(Click here)

Hide 89510D 5.REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.
C442430N01
2.938,0.469 3.208,0.76 0.271,0.292 18 true i 3.5,1.385 3.771,1.677 0.271,0.292 18 true ii

i.

Disconnect the connector from the brake pedal stroke sensor assembly.


ii.

Remove the 2 nuts and brake pedal stroke sensor assembly from the brake pedal support assembly.

NOTICE:
·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.