Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (for HV Model RHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480868 BRAKE MASTER CYLINDER(for HV Model RHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for HV Model RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C460951N02
3.917,3.208 4.833,3.542 0.917,0.333 3.875,3.167 4.875,3.583 1,0.417 1.042,2.781 1.792,2.948 0.75,0.167 1,2.74 1.833,2.99 0.833,0.25 1.417,2.781 1.417,2.448 false 3.885,1.958 3.885,1.625 false 2.375,0.667 2.75,0.333 2.75,0.333 2.917,0.333 false 3.417,3.417 2.833,3.417 2.833,3.417 2.833,2.917 false 3,3.417 3,2.948 false 3.677,3.24 3.958,3.594 0.281,0.354 18 false 3 3.167,0.167 3.448,0.521 0.281,0.354 18 false 2 3.917,1.958 4.198,2.313 0.281,0.354 18 false 1 3.781,1.969 3.938,2.167 0.156,0.198 10 false ● 0.833,2.75 0.99,2.948 0.156,0.198 10 false ● 1.448,2.406 1.76,2.604 0.313,0.198 10 false x2 3.969,3.219 5.688,3.375 1.719,0.156 8 false 19.5 (199, 14) 3.969,3.385 5.688,3.542 1.719,0.156 8 false 17.4 (177, 13)* 1.083,2.781 2.552,2.938 1.469,0.156 8 false 20 (204, 15)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE MASTER CYLINDER O-RING - - - -
2 BRAKE MASTER CYLINDER SUB-ASSEMBLY 47201 (Click here) - -
3 CONNECT BRAKE LINE - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) * For use with a union nut wrench
● Non-reusable part - -

C460965N01
1.115,1.375 1.781,1.542 0.667,0.167 3.063,0.927 3.396,0.927 false 4.302,1.51 4.635,1.51 false 5.302,2.083 5.635,2.083 false 4.5,3.375 4.833,3.375 false 6.417,0.302 6.75,0.302 false 1.781,1.458 2.115,1.458 false 5.688,1.906 5.969,2.26 0.281,0.354 18 false 6 4.677,1.333 4.958,1.688 0.281,0.354 18 false 7 3.438,0.76 3.719,1.115 0.281,0.354 18 false 8 4.896,3.229 5.177,3.583 0.281,0.354 18 false 5 6.198,0.146 6.479,0.5 0.281,0.354 18 false 4 2.26,1.354 2.719,1.552 0.458,0.198 10 false x12 1.156,1.375 2.51,1.531 1.354,0.156 8 false 12 (122, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

4 BLEED BRAKE LINE - (Click here) - -
5 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
6 WATER GUARD PLATE LH 55735A - - -
7 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
8 WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY - - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 1.INSTALL BRAKE MASTER CYLINDER O-RING

Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

Z101186

NOTICE:

When installing a new brake master cylinder sub-assembly, remove the protectors from the master cylinder piston and outlet ports.



a.
C460963N01
0.396,0.083 0.677,0.438 0.281,0.354 18 false i 0.188,1.917 0.771,2.26 0.583,0.344 18 false ii, iii 3.906,0.979 4.49,1.323 0.583,0.344 18 false iv

i.

Install the brake master cylinder sub-assembly to the brake booster assembly with 2 new nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:
·

The brake master cylinder sub-assembly requires careful handling. Do not drop or subject the brake master cylinder sub-assembly to any impact. Do not reuse a brake master cylinder sub-assembly that has been dropped.

·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its reservoir when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, or cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of new and dry cloth. Do not use water or detergent. Then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




ii.

Engage the clamp to the brake master cylinder sub-assembly.


iii.

Connect the connector.


iv.

Connect the connector to the brake master cylinder reservoir assembly.



Hide 3.CONNECT BRAKE LINE

Z101186

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




a.
C460964C01
5.49,1.24 5.802,1.396 0.313,0.156 10 false *a 0.979,0.052 1.208,0.458 0.229,0.406 18 false i
*a Torque Wrench Fulcrum Length - -


i.

Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)





Hide 55701J 5.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55735A 6.INSTALL WATER GUARD PLATE LH

Hide 55815E 7.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 8.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY