Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (for Gasoline Model LHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480870 BRAKE MASTER CYLINDER(for Gasoline Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for Gasoline Model LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C460966N01
2.667,0.5 3,0.5 false 3.385,0.917 3.719,0.917 false 6.448,0.333 6.781,0.333 false 5.365,2 5.698,2 false 4.594,3.333 4.927,3.333 false 3.604,4.167 3.938,4.167 false 5.729,1.823 6.01,2.177 0.281,0.354 18 false 1 3.802,0.75 4.083,1.104 0.281,0.354 18 false 2 3.052,0.333 3.333,0.688 0.281,0.354 18 false 3 4.99,3.177 5.271,3.531 0.281,0.354 18 false 4 4,4 4.281,4.354 0.281,0.354 18 false 5 6.219,0.167 6.5,0.521 0.281,0.354 18 false 6 2.333,1.333 2.792,1.531 0.458,0.198 10 false x11

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY - - - -
2 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
3 WATER GUARD PLATE RH 55734A - - -
4 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
5 BATTERY 28800 - - -
6 DRAIN BRAKE FLUID - - (Click here) -

C460967N01
0.333,3.25 2.25,4.25 1.917,1 0.938,2.969 0.938,2.635 false 4.167,3.49 4.167,3.156 false 1.125,3.833 0.792,3.833 false 4,2 3.833,2 3.833,2 3.5,2.167 false 1.208,1.896 1.208,0.583 1.208,0.583 1.583,0.583 true 1.5,1.917 1.5,0.583 true 0.594,3.667 0.875,4.021 0.281,0.354 18 false 7 4.271,1.823 4.552,2.177 0.281,0.354 18 false 9 4.156,3.49 4.573,3.844 0.417,0.354 18 false 10 4.021,3.531 4.177,3.729 0.156,0.198 10 false ● 0.885,2.979 1.042,3.177 0.156,0.198 10 false ● 1.906,0.406 2.188,0.76 0.281,0.354 18 false 8 0.979,2.604 1.292,2.802 0.313,0.198 10 false x2 0.396,3.292 0.771,3.531 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

7 NO. 1 CLUTCH RESERVOIR HOSE 31434E - - -
8 BRAKE LINE - (Click here) - -
9 BRAKE MASTER CYLINDER SUB-ASSEMBLY 47201 (Click here) - -
10 BRAKE MASTER CYLINDER O-RING - - - -

*A for Manual Transaxle - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake master cylinder sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 2.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 4.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 6.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 31434E 7.DISCONNECT NO. 1 CLUTCH RESERVOIR HOSE (for Manual Transaxle)

a.
C460968


Hide 8.DISCONNECT BRAKE LINE

Z101186

NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




a.
C460969N01
1.625,0.115 1.906,0.469 0.281,0.354 18 false i

i.

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.



Hide 47201 9.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

a.
C460970C01
4.219,0.208 4.479,0.51 0.26,0.302 18 false iii 0.073,0.073 0.458,0.385 0.385,0.313 18 true i, ii
V113147

Push in this direction
V113148

Disconnect the connector


i.

Disconnect the connector from the brake master cylinder reservoir assembly.


ii.

Disengage the 2 clamps from the brake master cylinder sub-assembly.


iii.

Remove the 2 nuts and brake master cylinder sub-assembly from the brake booster assembly.

NOTICE:
·

The brake master cylinder sub-assembly requires careful handling. Do not drop or subject the brake master cylinder sub-assembly to any impact. Do not reuse a brake master cylinder sub-assembly that has been dropped.

·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its reservoir when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, or cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of new and dry cloth. Do not use water or detergent. Then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.





Hide 10.REMOVE BRAKE MASTER CYLINDER O-RING

a.
C460971