Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (for Gasoline Model LHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480870 BRAKE MASTER CYLINDER(for Gasoline Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for Gasoline Model LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C460983N01
0.167,3.25 2.167,4.25 2,1 2.167,0.375 3,0.708 0.833,0.333 2.125,0.333 3.042,0.75 0.917,0.417 0.604,2.969 1.271,3.135 0.667,0.167 0.563,2.927 1.313,3.177 0.75,0.25 0.938,2.969 0.938,2.635 false 4.167,3.49 4.167,3.156 false 1.188,3.667 0.75,3.667 false 4,2 3.833,2 3.833,2 3.5,2.167 false 1.208,1.896 1.208,0.583 1.208,0.583 1.583,0.583 true 1.5,1.917 1.5,0.583 true 0.542,3.542 0.823,3.896 0.281,0.354 18 false 4 4.271,1.823 4.552,2.177 0.281,0.354 18 false 2 4.156,3.49 4.573,3.844 0.417,0.354 18 false 1 4.021,3.531 4.177,3.729 0.156,0.198 10 false ● 0.448,2.948 0.604,3.146 0.156,0.198 10 false ● 1.906,0.406 2.188,0.76 0.281,0.354 18 false 3 0.979,2.604 1.292,2.802 0.313,0.198 10 false x2 0.208,3.271 0.583,3.51 0.375,0.24 12 false *A 2.198,0.396 3.917,0.552 1.719,0.156 8 false 19.5 (199, 14) 2.198,0.552 3.917,0.708 1.719,0.156 8 false 17.4 (177, 13)* 0.615,2.969 2.083,3.125 1.469,0.156 8 false 20 (204, 15)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE MASTER CYLINDER O-RING - - - -
2 BRAKE MASTER CYLINDER SUB-ASSEMBLY 47201 (Click here) - -
3 BRAKE LINE - (Click here) - -
4 NO. 1 CLUTCH RESERVOIR HOSE 31434E (Click here) - -

*A for Manual Transaxle - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) * For use with a union nut wrench
● Non-reusable part - -

C461344N01
1.156,1.313 1.823,1.479 0.667,0.167 2.667,0.5 3,0.5 false 3.385,0.917 3.719,0.917 false 6.458,0.271 6.792,0.271 false 5.365,2 5.698,2 false 4.594,3.333 4.927,3.333 false 3.604,4.167 3.938,4.167 false 1.823,1.396 2.156,1.396 false 5.729,1.823 6.333,2.281 0.604,0.458 18 false 11 3.802,0.75 4.385,1.125 0.583,0.375 18 false 10 3.052,0.333 3.333,0.688 0.281,0.354 18 false 9 4.99,3.177 5.271,3.531 0.281,0.354 18 false 8 4,4 4.281,4.354 0.281,0.354 18 false 7 5.583,0.125 6.458,0.469 0.875,0.344 18 false 5, 6 2.333,1.333 2.792,1.531 0.458,0.198 10 false x11 6.073,0.177 6.813,0.417 0.74,0.24 12 false (*A) 1.198,1.313 2.552,1.469 1.354,0.156 8 false 12 (122, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

5 BLEED BRAKE SYSTEM - (Click here) - -
6 BLEED CLUTCH LINE - (Click here) - -
7 BATTERY 28800 - - -
8 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
9 WATER GUARD PLATE RH 55734A - - -
10 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
11 WINDSHIELD WIPER MOTOR AND LINK - - - -

*A for Manual Transaxle - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 1.INSTALL BRAKE MASTER CYLINDER O-RING

Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

Z101186

NOTICE:

When installing a new brake master cylinder sub-assembly, remove the protectors from the master cylinder piston and outlet ports.



a.

for Manual Transaxle:

C460978C02
2.021,0.073 2.302,0.427 0.281,0.354 18 false i 3.51,1.406 3.823,1.604 0.313,0.198 10 false *a
*a More than 23.5 mm (0.925 in.) - -


i.

When installing a new brake master cylinder reservoir assembly or a new brake master cylinder sub-assembly, cut off the clutch tube tip of the brake master cylinder reservoir assembly as shown in the illustration.

CAUTION:

Be careful not to cut your finger on the cut surface.


NOTICE:
·

Do not allow any foreign matter to enter the brake master cylinder reservoir assembly.

·

Make sure that fluid supply is not affected by cutting the tube.





b.
C460979N01
0.406,0.063 0.688,0.417 0.281,0.354 18 false i 3.688,0.063 4.281,0.385 0.594,0.323 18 false ii, iii

i.

Install the brake master cylinder sub-assembly to the brake booster assembly with 2 new nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:
·

The brake master cylinder sub-assembly requires careful handling. Do not drop or subject the brake master cylinder sub-assembly to any impact. Do not reuse a brake master cylinder sub-assembly that has been dropped.

·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its reservoir when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, or cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of new and dry cloth. Do not use water or detergent. Then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




ii.

Engage the 2 clamps to the brake master cylinder sub-assembly.


iii.

Connect the connector to the brake master cylinder reservoir assembly.



Hide 3.CONNECT BRAKE LINE

Z101186

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




a.
C460980C01
5.479,1.188 5.792,1.385 0.313,0.198 10 false *a 0.781,0.073 1.063,0.427 0.281,0.354 18 false i
*a Torque Wrench Fulcrum Length - -


i.

Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)





Hide 31434E 4.CONNECT NO. 1 CLUTCH RESERVOIR HOSE (for Manual Transaxle)

a.
C460981C01
4.823,0.792 5.24,0.792 true 4.625,0.667 4.938,0.865 0.313,0.198 10 false *a 0.99,0.031 1.198,0.354 0.208,0.323 18 false i 5,0.313 5.313,0.51 0.313,0.198 10 false 30° 5.625,0.469 5.938,0.667 0.313,0.198 10 false 90°
*a Paint Mark - -
V100136

Up - -


i.

Connect the No. 1 clutch reservoir hose to the brake master cylinder reservoir assembly and slide the clip to secure it.

NOTICE:
·

When connecting the No. 1 clutch reservoir hose, face the paint mark up.

·

Make sure that the tabs of the clip are aligned as shown in the illustration.





Hide 6.BLEED CLUTCH LINE (for Manual Transaxle)

Hide 55701J 8.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55734A 9.INSTALL WATER GUARD PLATE RH

Hide 55815E 10.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 11.INSTALL WINDSHIELD WIPER MOTOR AND LINK