Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model TMC Made RHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480877 BRAKE BOOSTER(for HV Model TMC Made RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model TMC Made RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C442477N02
5.583,2.583 6.333,2.75 0.75,0.167 5.542,2.542 6.365,2.792 0.823,0.25 5.677,1.979 6.01,1.979 false 3.604,0.469 3.729,0.583 3.729,0.583 3.875,0.583 false 2.729,0.781 3.063,0.781 false 5.167,3.01 5.5,3.01 false 3.26,3.021 3.344,3.365 3.344,3.365 3.521,3.365 false 5.917,2.333 5.917,2.583 false 4.219,0.469 4.5,0.823 0.281,0.354 18 false 4 6.208,1.823 6.49,2.177 0.281,0.354 18 false 1 5.844,2.906 6.125,3.26 0.281,0.354 18 false 3 3.875,3.25 4.156,3.604 0.281,0.354 18 false 2 6.031,2.271 6.313,2.49 0.281,0.219 10 false x4 2.542,0.688 2.823,0.906 0.281,0.219 10 false ● 6.073,1.885 6.354,2.104 0.281,0.219 10 false ● 5.656,2.594 6.521,2.792 0.865,0.198 8 false 12.7 (130, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE BOOSTER GASKET 44785 - - -
2 BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 47210L (Click here) - -
3 PUSH ROD PIN 47264A (Click here) - -
4 BRAKE PEDAL RETURN SPRING 47101A (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V100135

Lithium soap base glycol grease - -

C463597N01
2.365,4.688 3.219,5.021 0.854,0.333 2.323,4.646 3.271,5.063 0.948,0.417 6.458,0.26 6.792,0.26 false 6.448,0.729 6.781,0.729 false 1.698,1.208 2.198,1.208 false 4.167,5 4.625,5 false 3.823,0.854 4.188,0.854 false 6.406,1.146 6.74,1.146 false 5.656,3.344 6.083,3.344 false 3.615,4.302 3.615,4.875 true 3.719,4.448 3.719,4.865 3.719,4.865 3.219,4.865 true 3.427,4.156 3.427,4.854 true 5.417,4.604 5.25,4.604 5.25,4.604 5.094,4.229 false 6.427,1.51 6.719,1.51 false 2.125,4.729 2.406,5.083 0.281,0.354 18 false 5 4.438,0.688 4.906,1.052 0.469,0.365 18 false 16 2.531,1.094 2.813,1.448 0.281,0.354 18 false 8 5.75,4.479 6.031,4.833 0.281,0.354 18 false 7 6.396,3.208 6.813,3.563 0.417,0.354 18 false 10 4.667,4.917 4.938,5.146 0.271,0.229 10 false ● 5.417,0.125 6.854,0.469 1.438,0.344 18 false 9, 14, 15 6.115,0.604 6.479,0.969 0.365,0.365 18 false 11 6.104,1.01 6.469,1.375 0.365,0.365 18 false 12 2.427,4.708 3.26,4.885 0.833,0.177 8 false 15.2 (155, 11) 2.417,4.865 3.271,5.042 0.854,0.177 8 false 13.4 (137, 10)* 4.823,4.875 5.104,5.229 0.281,0.354 18 false 6 6.115,1.385 6.479,1.75 0.365,0.365 18 false 13

Procedure Part Name Code
Z101186

Z101188

Z101187

5 BRAKE LINE - (Click here) - -
6 NO. 4 BRAKE TUBE CLAMP 47374B - - -
7 NO. 2 BRAKE ACTUATOR HOSE 44572C (Click here) - -
8 ENGINE ROOM MAIN WIRE 82111 (Click here) - -
9 BLEED NO. 1 BRAKE ACTUATOR TUBE 44551C (Click here) - -
10 BRAKE BOOSTER PUMP CONNECTOR - (Click here) - -
11 FILL RESERVOIR WITH BRAKE FLUID - - (Click here) -
12 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
13 UPDATE ECU SECURITY KEY - - - (Click here)
14 BLEED BRAKE SYSTEM - (Click here) - -
15 INSPECT AND ADJUST BRAKE PEDAL - (Click here) - -
16 INSTALL NO. 1 AIR DUCT 87211 (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) * For use with a union nut wrench
● Non-reusable part - -

C442470N03
0.854,1.354 1.521,1.521 0.667,0.167 6.542,0.177 6.875,0.177 false 5.208,0.927 5.542,0.927 false 3.594,1.281 3.927,1.281 false 4.521,2.083 4.854,2.083 false 4.094,3.333 4.427,3.333 false 1.521,1.438 1.854,1.438 false 5.656,0.031 6.667,0.385 1.01,0.354 18 false 21 - 23 5.594,0.781 6.125,1.146 0.531,0.365 18 false 20 3.99,1.135 4.5,1.49 0.51,0.354 18 false 19 4.938,1.948 5.365,2.302 0.427,0.354 18 false 18 4.51,3.188 5.01,3.521 0.5,0.333 18 false 17 1.958,1.448 2.25,1.646 0.292,0.198 10 false x12 0.917,1.354 1.698,1.51 0.781,0.156 8 false 12 (122, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

17 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
18 WATER GUARD PLATE LH 55735A - - -
19 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
20 WINDSHIELD WIPER MOTOR AND LINK - - - -
21 PERFORM CALIBRATION - (Click here) - -
22 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - (Click here) - -
23 CHECK FOR AND CLEAR DTCS - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

CAUTION / NOTICE / HINT

NOTICE:

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C442476N03
0.354,0.042 0.635,0.396 0.281,0.354 18 false i 2.635,1.094 2.792,1.292 0.156,0.198 10 true 1 4.438,0.51 4.594,0.708 0.156,0.198 10 true 2 2.656,0.521 2.813,0.719 0.156,0.198 10 true 3 4.438,1.104 4.594,1.302 0.156,0.198 10 true 4

i.

Install the brake booster with master cylinder assembly with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Tighten the nuts in the order shown in the illustration.

·
C429884C03
1.375,0.688 1.375,0.438 1.375,0.438 1.208,0.438 false 1.76,0.594 2.094,0.594 false 0.51,1.667 0.51,1.333 false 0.771,1.167 0.771,0.917 0.771,0.917 0.604,0.917 false 2.302,1.771 2.302,1.438 false 1.771,0.76 2.104,0.76 false 1.021,0.375 1.333,0.573 0.313,0.198 10 false *1 2.146,0.542 2.458,0.74 0.313,0.198 10 false *2 0.438,1.667 0.75,1.865 0.313,0.198 10 false *3 0.427,0.854 0.74,1.052 0.313,0.198 10 false *4 2.219,1.792 2.531,1.99 0.313,0.198 10 false *5 2.146,0.719 2.458,0.917 0.313,0.198 10 false *6
*1 Skid Control ECU
*2 No. 1 Reservoir Hose
*3 Brake Master Cylinder Push Rod Clevis
*4 Boot
*5 Master Cylinder Reservoir Assembly
*6 Brake Actuator Bracket


Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Be careful not to allow brake fluid to enter the connector.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.





Hide 47264A 3.INSTALL PUSH ROD PIN

Z101186

Click here(Click here)

Hide 47101A 4.INSTALL BRAKE PEDAL RETURN SPRING

Z101186

Click here(Click here)

Hide 5.CONNECT BRAKE LINE

a.
C442479C02
2.479,1.188 2.792,1.344 0.313,0.156 10 false *a 0.302,0.021 0.583,0.375 0.281,0.354 18 false i
*a Torque Wrench Fulcrum Length - -


i.

Using a union nut wrench, connect the 3 brake lines to the brake booster with master cylinder assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)





Hide 47374B 6.INSTALL NO. 4 BRAKE TUBE CLAMP

Hide 44572C 7.CONNECT NO. 2 BRAKE ACTUATOR HOSE

Z101186

NOTICE:
·

Make sure to connect the No. 2 brake actuator hose with its identification mark facing the front of the vehicle.

·

Install the clip within the range shown in the illustration.




a.
C442480C02
4.146,1.198 4.385,0.74 true 4.042,1.198 4.26,1.375 0.219,0.177 10 true *a 2.208,0.583 2.667,0.781 0.458,0.198 10 false 90° 2.208,1.229 2.667,1.427 0.458,0.198 10 false 90°
*a Identification Mark
V100136

Front of the vehicle



Hide 82111 8.INSTALL ENGINE ROOM MAIN WIRE

a.
C442481C02
1.198,0.031 1.417,0.281 0.219,0.25 18 true i 2.75,0.719 2.969,0.969 0.219,0.25 18 true ii 4.448,0.938 4.75,1.188 0.302,0.25 18 true iii 5.698,0.969 6,1.219 0.302,0.25 18 true iv
V113147

Connect the connector
V113148

Lock the lock lever


i.

Connect the connector to the brake booster with master cylinder assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.




ii.

Engage the clamp to install the engine room main wire.


iii.

Engage the clamp.


iv.

Connect the connector to the brake booster with master cylinder assembly.



Hide 44551C 9.BLEED NO. 1 BRAKE ACTUATOR TUBE

Z101186

NOTICE:

Make sure to bleed the air from the No. 1 brake actuator tube. If the air remains in the No. 1 brake actuator tube, the air will enter the brake booster pump assembly and may damage the brake booster pump assembly.



a.
C442482C01
4.885,0.969 5.219,0.969 true 4.885,1.229 5.219,1.229 true 0.25,0.083 0.542,0.333 0.292,0.25 18 true i 3.708,0.083 4,0.333 0.292,0.25 18 true ii 0.25,2 0.542,2.25 0.292,0.25 18 true iii 3.667,2 3.958,2.25 0.292,0.25 18 true iv 4.625,0.896 4.844,1.063 0.219,0.167 10 true *a 4.635,1.146 4.854,1.313 0.219,0.167 10 true *b

i.

Remove the brake master cylinder reservoir filler cap assembly.


ii.

Add brake fluid to the reservoir until the fluid level is between the MAX and MIN lines on the brake fluid reservoir.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT3

SAE J1704 or FMVSS No. 116 DOT4



iii.

Remove the 4 bolts, 4 screws, 9 clips and No. 1 engine under cover assembly from the vehicle body.


iv.

Remove the 3 nuts and dash panel heat insulator.



b.
C429894N01
0.125,0.135 0.406,0.49 0.281,0.354 18 false i 4.542,0.667 4.823,1.021 0.281,0.354 18 false ii

i.

Remove the 2 nuts to separate the No. 1 brake actuator tube from the vehicle body.


ii.

Disengage the 4 clamps to remove the 2 No. 11 brake tube clamps.



c.
C442483N01
2.417,1.25 2.833,1.25 true 3.333,0.417 3.75,0.417 true 2.167,1.167 2.5,1.333 0.333,0.167 10 true SST 3,0.333 3.333,0.5 0.333,0.167 10 true SST 0.354,0.031 5.031,0.385 4.677,0.354 18 false i, ii, iii, iv, v

i.

Set SST to the brake master cylinder reservoir assembly.

SST
09992-00242  
09992-00350  


ii.

Using SST, increase and then maintain the pressure in the brake master cylinder reservoir assembly for 60 seconds.(*1)

Standard Pressure:

50 to 80 kPa (0.6 to 0.8 kgf/cm2, 7.3 to 11.6 psi)



iii.

Release the pressure in the brake master cylinder reservoir assembly and wait for 30 seconds.(*2)


iv.

Repeat steps *1 to *2, 3 times.


v.

Remove SST.



d.
C442484N02
2.802,0.021 3.344,0.271 0.542,0.25 18 true iii, v 0.375,0.021 0.854,0.271 0.479,0.25 18 true i, ii 5.146,0.021 5.74,0.281 0.594,0.26 18 true iv, v

i.

Pull up the No. 1 brake actuator tube as shown in the illustration as high as possible for 10 seconds without damaging the bracket of the No. 1 brake actuator tube.(*3)

NOTICE:

Do not damage the hoses.


HINT:

Elevating the No. 2 brake actuator hose causes any air in the horizontal portion of the hose to flow to the brake master cylinder reservoir assembly side.



ii.

Repeat step *3, 5 times.


iii.

Elevate the No. 1 brake actuator tube for 10 seconds by lifting the No. 1 brake actuator tube as shown in the illustration.(*4)

NOTICE:

Do not damage the hoses.


HINT:

Elevating the No. 1 brake actuator tube causes any air in the horizontal portion of the tube to flow to the brake master cylinder reservoir assembly side.



iv.

Lower the No. 1 brake actuator tube for 10 seconds as shown in the illustration.(*5)

NOTICE:

Do not damage the hoses.


HINT:

Lowering the No. 1 brake actuator tube causes any air in the No. 1 brake actuator tube to flow to the brake master cylinder reservoir assembly side.



v.

Repeat steps *4 to *5, 5 times.



e.
C429894N01
0.125,0.135 0.406,0.49 0.281,0.354 18 false i 4.542,0.667 4.823,1.021 0.281,0.354 18 false ii

i.

Install the No. 1 brake actuator tube with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


ii.

Engage the 4 clamps to install the 2 No. 11 brake tube clamps.



f.
C442485N01
0.385,0.063 0.667,0.344 0.281,0.281 18 false i 3.708,0.073 3.99,0.354 0.281,0.281 18 false ii

i.

Install the dash panel heat insulator with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.

Install the No. 1 engine under cover assembly with the 4 bolts, 4 screws and 9 clips.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 10.CONNECT BRAKE BOOSTER PUMP CONNECTOR

Z101186

HINT:

Perform this operation only when the accumulator pressure zero down could not be performed using the GTS.



a.
C442486C02
0.365,0.021 0.646,0.375 0.281,0.354 18 false i
V113147

Connect the connector
V113148

Lock the lock lever


i.

Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.





Hide 11.FILL RESERVOIR WITH BRAKE FLUID

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 15.INSPECT AND ADJUST BRAKE PEDAL

Hide 87211 16.INSTALL NO. 1 AIR DUCT

Z101186

Click here(Click here)

Hide 55701J 17.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55735A 18.INSTALL WATER GUARD PLATE LH

Hide 55815E 19.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 20.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 22. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART