Home › Suspension › REAR SUSPENSION › REAR COIL SPRING (for 2WD) › from 2021.07
RM3700E _53 Suspension _093739 REAR SUSPENSION _0441857 REAR COIL SPRING(for 2WD) A

REAR SUSPENSION  REAR COIL SPRING(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C459056N02
0.333,1.667 1.667,2.417 1.333,0.75 5.5,1.719 5.552,1.292 5.552,1.292 5.677,1.292 false 4.354,0.917 4.729,0.917 false 2.531,1.417 2.677,1.417 2.677,1.417 2.823,1.979 false 4.802,3.25 5.094,3.25 false 2.917,3.042 3.417,3.042 false 3.99,3.979 4.365,3.698 4.365,3.698 4.49,3.698 false 5.052,5.156 5.354,5.156 false 1.396,5.521 1.542,5.521 1.542,5.521 1.885,5.323 false 0.25,3.75 0.417,3.75 0.417,3.75 0.552,3.542 false 0.51,3.135 0.677,3.135 0.677,3.135 1.156,3.427 false 5.604,2.708 6,2.708 false 6.563,0.188 6.854,0.188 false 0.792,2.104 1.125,2.104 false 5.063,0.75 5.844,1.125 0.781,0.375 18 false 7 5.958,1.125 6.406,1.438 0.448,0.313 18 false 12 2.208,1.24 2.75,1.646 0.542,0.406 18 false 11 4.615,3.104 4.896,3.458 0.281,0.354 18 false 5 3.708,2.875 3.99,3.229 0.281,0.354 18 false 6 4.74,3.573 5.135,3.906 0.396,0.333 18 false 12 4.854,5.021 5.135,5.375 0.281,0.354 18 false 3 1.083,5.354 1.865,5.729 0.781,0.375 18 false 11 0.063,3.615 0.344,3.969 0.281,0.354 18 false 4 0.823,2.875 1.104,3.229 0.281,0.354 10 false x2 5.917,3.063 6.198,3.417 0.281,0.354 10 false x2 5.542,0.063 5.823,0.417 0.281,0.354 18 false 1 5.979,0.052 6.354,0.417 0.375,0.365 18 false , 2 6.271,0.135 6.615,0.49 0.344,0.354 10 false (*A) 5.688,0.125 6.052,0.49 0.365,0.365 10 false (*A) 0.354,2.99 0.635,3.344 0.281,0.354 18 false 8 6.344,2.563 7.052,2.854 0.708,0.292 18 false 9 0.49,1.927 0.865,2.25 0.375,0.323 18 false 10 0.354,1.698 0.719,2.063 0.365,0.365 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - (Click here) - -
3 REAR WHEEL - - - -
4 REAR FLEXIBLE HOSE LH 47319F - - -
5 REAR FLEXIBLE HOSE RH 47318F - - -
6 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
7 NO. 1 PARKING BRAKE WIRE ASSEMBLY 890C0 (Click here) - -
8 REAR DISC BRAKE CALIPER ASSEMBLY LH - (Click here) - -
9 REAR DISC BRAKE CALIPER ASSEMBLY RH - (Click here) - -
10 REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH 89408C - - -
11 REAR AXLE BEAM ASSEMBLY 42110F (Click here) - -
12 SEPARATE REAR SHOCK ABSORBER ASSEMBLY - (Click here) - -

*A for HV Model TMC Made *B w/ Height Control Sensor

C444387N03
4.365,1.042 4.688,1.042 false 4.292,0.385 4.615,0.385 false 4.354,2.042 4.615,2.042 false 2.646,0.833 2.885,0.833 false 6.125,2.031 6.458,2.031 false 4.771,0.875 5.323,1.229 0.552,0.354 18 false 14 6.719,1.927 7.052,2.281 0.333,0.354 18 false 16 4.677,0.229 5.229,0.583 0.552,0.354 18 false 13 4.677,1.854 5.229,2.208 0.552,0.354 18 false 15 3.208,0.729 3.542,1.083 0.333,0.354 18 false 16

Procedure Part Name Code
Z101186

Z101188

Z101187

13 REAR UPPER COIL SPRING INSULATOR 48259A - - -
14 REAR COIL SPRING 48231B - - -
15 REAR LOWER COIL SPRING INSULATOR 48258C - - -
16 CONNECT REAR SHOCK ABSORBER ASSEMBLY - (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear coil spring removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Rear wheel alignment adjustment for HV Model TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for HV Model TMMF Made:
1.

Perform "Reset Memory"

2.

Perform calibration (brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
w/ Advanced Park:

Advanced Park


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system w/o Advanced Park:
(Click here)
w/ Advanced Park:
(Click here)
w/ Advanced Park:

Advanced Park


(Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model TMC Made)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL (for HV Model TMC Made)

Hide 3.REMOVE REAR WHEEL

Hide 47319F 4.SEPARATE REAR FLEXIBLE HOSE LH

a.
C445962


Hide 47318F 5.SEPARATE REAR FLEXIBLE HOSE RH

a.

Perform the same procedure as for the LH side.


Hide 6.SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C443644N01
0.375,0.042 0.656,0.396 0.281,0.354 18 false i 3.635,0.052 3.917,0.406 0.281,0.354 18 false ii 1.927,2.01 2.208,2.365 0.281,0.354 18 false iii

i.

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




ii.

Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.

NOTICE:

Be careful not to damage the rear axle hub and bearing assembly or connector cover.



iii.

Remove the 2 nuts and separate the No. 2 parking brake wire assembly.



Hide 7.SEPARATE NO. 1 PARKING BRAKE WIRE ASSEMBLY

a.

Perform the same procedure as for the No. 2 side.


Hide 8.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH

Z101186

Click here(Click here)

Hide 9.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 89408C 10.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 11.LOOSEN REAR AXLE BEAM ASSEMBLY

a.
C444388N01
0.375,0.073 0.656,0.427 0.281,0.354 18 false i

i.

Loosen the 2 bolts.

NOTICE:

Do not remove the bolts.




Hide 12.SEPARATE REAR SHOCK ABSORBER ASSEMBLY

a.
C443645N01
0.406,0.042 0.823,0.344 0.417,0.302 18 false i, ii

i.

Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.

CAUTION:

Do not jack up the rear axle beam assembly too high as the vehicle may fall.



ii.

Remove the 2 bolts and 2 nuts, and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

NOTICE:

Because the nuts have their own stoppers, do not turn the nuts. Loosen the bolts with the nuts secured.




Hide 48259A 13.REMOVE REAR UPPER COIL SPRING INSULATOR

a.
C443646


Hide 14.REMOVE REAR COIL SPRING

a.
C443647


Hide 48258C 15.REMOVE REAR LOWER COIL SPRING INSULATOR

a.
C443648


Hide 16.CONNECT REAR SHOCK ABSORBER ASSEMBLY

a.
C449038N03
0.396,0.042 0.677,0.396 0.281,0.354 18 false i

i.

Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily install the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts and 2 nuts.

NOTICE:

Because the nuts have their own stoppers, do not turn the nuts. Loosen the bolts with the nuts secured.