Home › Suspension › REAR SUSPENSION › REAR COIL SPRING (for AWD) › from 2021.07
RM3700E _53 Suspension _093739 REAR SUSPENSION _0441864 REAR COIL SPRING(for AWD) A

REAR SUSPENSION  REAR COIL SPRING(for AWD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C444392N04
0.635,0.094 2.313,1.51 1.677,1.417 3.25,0.365 5.167,1.802 1.917,1.438 6.063,3.031 6.333,3.031 false 4.323,1.302 4.156,1.583 4.156,1.583 3.99,1.583 false 1.25,1.302 1.521,1.302 false 6.396,2.844 6.677,3.198 0.281,0.354 18 false 1 1.052,1.135 1.333,1.49 0.281,0.354 18 false 3 3.792,1.427 4.073,1.781 0.281,0.354 18 false 2 0.698,0.146 0.979,0.5 0.281,0.354 12 false *B 3.333,0.406 3.615,0.76 0.281,0.354 12 false *A 1.719,0.26 2,0.615 0.281,0.354 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR AXLE HUB AND BEARING ASSEMBLY 42450B - - -
2 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A - - -
3 NO. 1 PARKING BRAKE WIRE ASSEMBLY 890C0 - - -

*A for LH Side *B for RH Side

C444393N02
2.688,2.844 2.688,3.146 false 4.406,1.375 4.917,1.375 false 4.281,0.417 4.573,0.417 false 5.365,2.125 5.521,2.125 5.521,2.125 6.302,1.458 false 3.833,2.167 4.125,2.167 false 3.646,4.938 3.646,5.24 false 3.583,5.24 3.865,5.594 0.281,0.354 18 false 5 5.156,1.958 5.531,2.313 0.375,0.354 18 false 6 5.156,1.177 5.531,1.531 0.375,0.354 18 false 7 4.656,0.24 5.031,0.594 0.375,0.354 18 false 8 3.625,1.979 4,2.333 0.375,0.354 18 false 9 2.625,3.135 3,3.49 0.375,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

4 REAR UPPER CONTROL ARM ASSEMBLY 48790 - - -
5 LOWER CONTROL ARM ASSEMBLY 48730 - - -
6 REAR SHOCK ABSORBER ASSEMBLY 48540 (Click here) - -
7 REAR COIL SPRING 48231B (Click here) - -
8 REAR UPPER COIL SPRING INSULATOR 48259A - - -
9 REAR LOWER COIL SPRING INSULATOR 48258C - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear coil spring removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Rear wheel alignment adjustment for TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for TMMF Made:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
w/ Advanced Park:

Advanced Park


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system w/o Advanced Park:
(Click here)
w/ Advanced Park:
(Click here)
w/ Advanced Park:

Advanced Park


(Click here)

HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Hide 890C0A 2.SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY (for LH Side)

a.
C443651


Hide 890C0 3.SEPARATE NO. 1 PARKING BRAKE WIRE ASSEMBLY (for RH Side)

a.
C443652N01
0.313,0.042 0.594,0.396 0.281,0.354 18 false i 3.719,0.073 4,0.427 0.281,0.354 18 false ii 1.927,2.01 2.208,2.365 0.281,0.354 18 false iii


Hide 48790 4.REMOVE REAR UPPER CONTROL ARM ASSEMBLY

Hide 48730 5.REMOVE LOWER CONTROL ARM ASSEMBLY

Hide 48540 6.DISCONNECT REAR SHOCK ABSORBER ASSEMBLY

a.
C443653N01
0.885,0.063 1.063,0.344 0.177,0.281 18 true i 3.896,0.052 4.094,0.365 0.198,0.313 18 false ii

i.

Support the spring seat of the rear No. 1 suspension arm assembly using jack and wooden block.

NOTICE:

Do not jack up the rear No. 1 suspension arm assembly too high as the vehicle may fall.



ii.

Remove the bolt and separate the rear No. 1 suspension arm assembly from the rear shock absorber assembly.



Hide 48231B 7.REMOVE REAR COIL SPRING

a.
C443654N01
0.375,0.042 0.656,0.396 0.281,0.354 18 false i

i.

Slowly lower the rear No. 1 suspension arm assembly using jacks and wooden block, and remove the rear coil spring.



Hide 48259A 8.REMOVE REAR UPPER COIL SPRING INSULATOR

a.
C429402


Hide 48258C 9.REMOVE REAR LOWER COIL SPRING INSULATOR

a.
C429401