Home › Suspension › REAR SUSPENSION › REAR TRAILING ARM › from 2021.07
RM3700E _53 Suspension _093739 REAR SUSPENSION _0441860 REAR TRAILING ARM A

REAR SUSPENSION  REAR TRAILING ARM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C444400N02
2.052,1.573 1.792,1.156 1.792,1.156 1.625,1.156 false 1.365,3.406 1.583,3.406 false 4.521,0.656 4.854,0.656 false 5.854,2.052 6.156,2.052 false 1.01,2.469 1.354,2.469 false 0.792,2.302 1.073,2.656 0.281,0.354 18 false 4 2.958,2.844 3.198,3.104 0.24,0.26 10 false x4 1.417,0.979 1.698,1.333 0.281,0.354 18 false 2 1.156,3.25 1.438,3.604 0.281,0.354 18 false 3 3.531,3.781 3.813,4.135 0.281,0.354 18 false 5 4.927,0.469 5.208,0.823 0.281,0.354 18 false 1 6.208,1.927 6.49,2.281 0.281,0.354 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR LOWER COIL SPRING INSULATOR 48258C - - -
2 REAR NO. 2 SUSPENSION TOE ADJUST PLATE 48452R (Click here) - -
3 TOE ADJUST CAM SUB-ASSEMBLY - - - -
4 REAR SUSPENSION ARM BRACKET ASSEMBLY 48070 - - -

*1 REAR NO. 1 SUSPENSION ARM ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear coil spring removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Rear wheel alignment adjustment for TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for TMMF Made:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
w/ Advanced Park:

Advanced Park


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system w/o Advanced Park:
(Click here)
w/ Advanced Park:
(Click here)
w/ Advanced Park:

Advanced Park


(Click here)

HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48258C 1.REMOVE REAR LOWER COIL SPRING INSULATOR

Hide 48452R 2.REMOVE NO. 2 REAR SUSPENSION TOE ADJUST PLATE

a.
C443663C01
1.802,0.677 1.896,0.979 1.896,0.979 1.896,0.677 true 0.875,1.333 0.625,0.792 0.625,0.792 0.969,1.333 true 0.885,0.052 1.063,0.323 0.177,0.271 18 true i 4.208,0.052 4.427,0.323 0.219,0.271 18 true ii 0.49,0.667 0.698,0.865 0.208,0.198 10 true *a 1.844,0.979 2.052,1.177 0.208,0.198 10 true *a
*a Matchmark - -


i.

Place matchmarks on the rear No. 2 suspension toe adjust plate, toe adjust cam sub-assembly and rear suspension arm bracket assembly.


ii.

Remove the nut and No. 2 rear suspension toe adjust plate.



Hide 3.REMOVE TOE ADJUST CAM SUB-ASSEMBLY

a.
C443664


Hide 48070 4.REMOVE REAR SUSPENSION ARM BRACKET ASSEMBLY

a.
C443665