Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE › from 2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441823 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C462335N02
0.167,0.167 6.5,3.667 6.333,3.5 5.854,2.438 5.688,2.438 5.688,2.438 5.49,2.781 false 1.604,2.792 1.906,2.792 false 4.406,1.042 4.24,1.042 4.24,1.042 4.042,1.385 false 2.74,0.563 2.573,0.563 2.573,0.563 2.375,0.906 false 6.5,1.833 6.74,1.833 false 1,1.146 1.333,1.146 false 2.771,0.458 3.052,0.813 0.281,0.354 10 false *1 1.604,0.49 1.885,0.844 0.281,0.354 10 false x3 6.156,2.302 6.365,2.656 0.208,0.354 18 false 3 4.458,0.896 4.74,1.25 0.281,0.354 18 false 4 1.448,2.656 1.729,3.01 0.281,0.354 18 false 2 6.792,1.708 7.073,2.063 0.281,0.354 18 false 1 0.865,1.052 1.146,1.385 0.281,0.333 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT AXLE ASSEMBLY - - - -
2 FRONT LOWER BALL JOINT ASSEMBLY 43340A (Click here) - -
3 FRONT AXLE HUB SUB-ASSEMBLY 43502C (Click here) - -
4 FRONT DISC BRAKE DUST COVER 47782 - - -

*1 STEERING KNUCKLE - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the steering knuckle removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model TMC Made:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Front wheel alignment adjustment for HV Model TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for HV Model TMMF Made:
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
w/ Advanced Park:

Advanced Park


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system w/o Advanced Park:
(Click here)
w/ Advanced Park:
(Click here)
w/ Advanced Park:

Advanced Park


(Click here)

HINT:
for HV Model TMC Made

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY

Hide 43340A 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

Z101186

Click here(Click here)

Hide 43502C 3.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C443135N03
0.396,0.073 0.833,0.385 0.438,0.313 18 false i, ii

i.

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



ii.

Remove the 3 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.





Hide 47782 4.REMOVE FRONT DISC BRAKE DUST COVER

a.
C443136