Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) › from 2021.07
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438027 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C449789N01
2.115,1.104 1.573,1.104 false 1.385,0.958 1.667,1.313 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 MANIFOLD STAY 17118 (Click here) - -

C463075N01
0.302,3.417 1.031,3.583 0.729,0.167 5.865,1.875 6.594,2.042 0.729,0.167 2.771,1 3.125,1 false 0.865,2.688 1.354,2.688 false 5.49,1.271 5.844,1.271 false 1.219,3.948 1.583,3.948 false 1.542,5.042 1.906,5.042 false 5.927,4.573 6.24,4.573 false 6.177,4.073 6.427,4.073 false 6.042,3.094 6.177,2.823 6.177,2.823 6.344,2.823 false 0.667,3.406 0.667,3.115 false 6.24,1.875 6.24,1.583 false 0.906,4.604 1.271,4.604 false 4.281,5.125 4.281,5.458 false 6.49,3.927 6.771,4.281 0.281,0.354 18 false 2 6.823,2.677 7.104,3.031 0.281,0.354 18 false 3 4.219,5.469 4.5,5.781 0.281,0.313 18 false 4 6.219,1.104 6.5,1.458 0.281,0.354 18 false 5 3.458,0.885 3.74,1.24 0.281,0.354 18 false 6 6.604,4.438 6.885,4.792 0.281,0.354 18 false 7 1.354,4.917 1.635,5.271 0.281,0.354 18 false 8 1.021,3.823 1.302,4.177 0.281,0.354 18 false 9 1.313,4.458 1.792,4.802 0.479,0.344 18 false 10 0.75,3.094 1.063,3.292 0.313,0.198 10 false x2 6.323,4.823 6.635,5.021 0.313,0.198 10 false x2 6.177,3.052 6.49,3.25 0.313,0.198 10 false *a 6.333,1.479 6.646,1.677 0.313,0.198 10 false x2 0.646,2.583 0.927,2.938 0.281,0.354 18 false 5 0.365,3.427 1.177,3.656 0.813,0.229 8 false 43 (438, 32) 5.927,1.885 6.74,2.115 0.813,0.229 8 false 43 (438, 32) 6.677,2.729 6.833,2.927 0.156,0.198 10 false ★

Procedure Part Name Code
Z101186

Z101188

Z101187

2 FLYWHEEL HOUSING UNDER COVER 11361J - - -
3 DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT - (Click here) - -
4 ENGINE ASSEMBLY WITH TRANSAXLE - - - -
5 ENGINE HANGERS - (Click here) - -
6 ENGINE WIRE 82121 (Click here) - -
7 TCM 89535B (Click here) - -
8 NO. 4 WATER BY-PASS HOSE 16281N - - -
9 NO. 3 WATER BY-PASS HOSE ASSEMBLY 16290F - - -
10 STARTER ASSEMBLY 28100 - - -

*a Black Color: x1
Silver Color: x5
- -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ★ Precoated part

C462293N01
3.271,0.365 3.813,0.365 false 4.24,2.635 4.354,2.333 4.354,2.333 4.521,2.333 false 3.167,3.042 3.333,3.042 3.333,3.042 3.427,2.729 false 2.01,5.406 2.177,5.406 2.177,5.406 2.49,5.146 false 5.167,5.104 5.313,5.417 5.313,5.417 5.479,5.417 false 6.156,3.021 6.458,3.021 false 4.125,0.24 4.677,0.594 0.552,0.354 18 false 11 2.833,2.917 3.385,3.271 0.552,0.354 18 false 12 4.948,2.167 5.5,2.521 0.552,0.354 18 false 13 4.854,2.219 5.031,2.458 0.177,0.24 10 false ● 5.5,5.25 6.052,5.604 0.552,0.354 18 false 14 1.677,5.281 2.229,5.635 0.552,0.354 18 false 15 1.917,2.875 2.198,3.146 0.281,0.271 10 false x5 2.594,5.531 2.875,5.802 0.281,0.271 10 false x3 6.49,2.927 6.771,3.198 0.281,0.271 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

11 ENGINE ASSEMBLY - (Click here) - -
12 REMOVE TORQUE CONVERTER ASSEMBLY 32000A (Click here) - -
13 CVT OIL PUMP TYPE T OIL SEAL 30400E (Click here) - -
14 FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY 51201 - - -
15 NO. 2 ENGINE MOVING CONTROL ROD 12364B - - -

*1 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY - -
● Non-reusable part - -

C463073N01
5.25,0.417 6.583,1.5 1.333,1.083 3.917,0.417 5.25,1.5 1.333,1.083 4.677,0.688 4.344,0.688 false 6.073,1.25 5.74,1.25 false 6.281,1.74 5.948,1.74 false 3.885,1.792 3.552,1.792 false 2.708,2.135 2.375,2.135 false 1.156,2.208 0.823,2.208 false 1.49,4.573 1.156,4.573 false 6.042,0.698 5.708,0.698 false 4.719,1.25 4.385,1.25 false 6.771,0.229 6.438,0.229 false 6.667,1.615 7.063,1.979 0.396,0.365 18 false 19 4.719,0.542 5.125,0.917 0.406,0.375 18 false 18 3.938,1.635 4.271,1.979 0.333,0.344 18 false 16 2.063,1.99 2.479,2.333 0.417,0.344 18 false 16 0.531,2.073 0.927,2.427 0.396,0.354 18 false 17 0.979,4.417 1.26,4.771 0.281,0.354 18 false 4 6.125,1.156 6.406,1.51 0.281,0.354 10 false ● 1.302,1.615 1.583,1.969 0.281,0.354 10 false x2 4,0.5 4.25,0.75 0.25,0.25 12 false *A 5.333,0.5 5.583,0.75 0.25,0.25 12 false *B 4.771,1.156 5.052,1.51 0.281,0.354 10 false ● 6.073,0.542 6.479,0.917 0.406,0.375 18 false 18 5.729,0.083 6.531,0.458 0.802,0.375 18 false 20, 21 6.552,1.656 6.833,2.01 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

16 WIRE HARNESS CLAMP BRACKET - - - -
17 NO. 1 TRANSMISSION CONTROL CABLE BRACKET 33823 - - -
18 TRANSMISSION CASE PLUG ASSEMBLY 35150B - - -
19 NO. 1 BREATHER PLUG 35141F (Click here) - -
20 INSPECT TORQUE CONVERTER ASSEMBLY 32000A (Click here) - -
21 INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY - (Click here) - -

*A for Type A *B for Type B
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
1.

Reset memory

2.

Transaxle compensation code (Input)

3.

CVT oil pressure calibration


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (w/o Advanced Park) (Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


Because the weight of the engine assembly with transaxle is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.

·
A344783

Do not touch the engine, exhaust manifold or other high temperature components when they are hot.

·

Touching the engine, exhaust manifold or other high temperature components when they are hot could result in burns.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 17118 1.REMOVE MANIFOLD STAY

Z101186

Click here(Click here)

Hide 11361J 2.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C431058C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 3.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C431059N01
0.5,0.083 0.667,0.333 0.167,0.25 18 false i

i.

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.




Hide 4.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 5.INSTALL ENGINE HANGERS

Z101186

Click here(Click here)

Hide 82121 6.DISCONNECT ENGINE WIRE

a.
C428822C10
0.49,0.135 1.021,0.698 0.531,0.563 18 false i, ii, iii, iv
V113147

Rotate in this Direction - -


i.

Disengage the 2 claws, rotate the 2 lock levers and disconnect the 2 connectors.


ii.

Disconnect the 6 connectors.


iii.

Remove the bolt and separate the engine wire from the continuously variable transaxle assembly.


iv.

Disengage the 4 clamps to separate the engine wire.



b.
C462297N01
0.354,0.177 0.51,0.542 0.156,0.365 18 false i 3.417,0.188 3.938,0.49 0.521,0.302 18 false ii, iii 1.938,2.813 2.292,3.125 0.354,0.313 18 false iv

i.

Separate the No. 3 water by-pass hose assembly.


ii.

Remove the bolt and disconnect the engine wire from the continuously variable transaxle assembly.


iii.

Disengage the 3 clamps to separate the engine wire.


iv.

Disengage the 3 clamps to separate the engine wire.



Hide 89535B 7.REMOVE TCM

Z101186

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to remove the TCM before disconnecting any of the coolant system hoses.



a.
C431050


Hide 16281N 8.DISCONNECT NO. 4 WATER BY-PASS HOSE

Hide 16290F 9.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 11.REMOVE ENGINE ASSEMBLY

Z101186

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.



a.
C431061N02
3.917,0.042 4.073,0.24 0.156,0.198 10 false A 2.875,0.208 3.031,0.406 0.156,0.198 10 false C 2.646,0.708 2.802,0.906 0.156,0.198 10 true C 2.813,1.344 2.969,1.542 0.156,0.198 10 true C 3.083,1.583 3.26,1.75 0.177,0.167 10 false C 4.01,1.573 4.156,1.729 0.146,0.156 10 false B 4.24,1.333 4.396,1.531 0.156,0.198 10 false C 0.479,0.094 0.76,0.448 0.281,0.354 18 false i

i.

Remove the 7 bolts and engine assembly from the continuously variable transaxle assembly.

HINT:
·

Bolt (A), (B): Remove from the continuously variable transaxle assembly side.

·

Bolt (C): Remove from the engine assembly side.





Hide 32000A 12.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C462336N01
0.385,0.052 0.667,0.406 0.281,0.354 18 false i

i.

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.




Hide 30400E 13.REMOVE CVT OIL PUMP TYPE T OIL SEAL

Z101186

NOTICE:
·

Do not remove the stator shaft assembly from the CVT main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.

·

Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.




a.
C431063C01
2.417,2.167 2,1.917 true 1.333,2.667 2.167,2.667 2.167,2.667 2.167,2.583 false 1.75,2.667 1.75,2.583 false 5.438,2.208 5.438,1.875 false 5,0.833 4.573,1.26 false 2.604,1.792 2.323,1.708 false 5.323,2.271 5.781,2.469 0.458,0.198 10 false SST 1.167,2.594 1.479,2.75 0.313,0.156 10 false *a 2.438,2.167 2.75,2.323 0.313,0.156 10 false *b 0.708,0.104 1.021,0.438 0.313,0.333 18 false i 3.521,0.083 3.833,0.417 0.313,0.333 18 false ii 5.063,0.76 5.375,0.917 0.313,0.156 10 false *1 2.656,1.719 3.115,1.917 0.458,0.198 10 false SST
*1 CVT Oil Pump Type T Oil Seal - -
*a Claw *b Center Bolt


i.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


ii.

Using SST, remove the CVT oil pump type T oil seal.

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the transaxle housing, as there is the possibility that metal particles could be produced if they do.




Hide 51201 14.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C462298


Hide 12364B 15.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C440414


Hide 16.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C431064


Hide 33823 17.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C431052


Hide 35150B 18.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C462337C01
0.583,0.083 0.958,0.323 0.375,0.24 12 false *A 4.167,0.083 4.542,0.323 0.375,0.24 12 false *B
*A for Type A *B for Type B



Hide 35141F 19.REMOVE NO. 1 BREATHER PLUG

Z101186

HINT:

Perform this procedure only when replacement of the No. 1 breather plug.



a.
C462677


Hide 32000A 20.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 21.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY