| *A | for CVT | *B | for Manual Transaxle |
| *C | for LHD | *D | for RHD |
| *A | for CVT | *B | for Manual Transaxle |
| *C | for LHD | *D | for RHD |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 44 | FRONT EXHAUST PIPE ASSEMBLY | 17410 | ( )
|
- | - |
| ● | Non-reusable part | - | - |
| *A | for CVT | *B | for Manual Transaxle |
| ★ | Precoated part | - | - |
| *a | BLACK COLOR: x1
SILVER COLOR: x5 |
- | - |
| *A | for CVT | *B | for Manual Transaxle |
| *a | for CVT: x5
for Manual Transaxle: x4 |
- | - |
| *A | for CVT | *B | for Manual Transaxle |
| *1 | CLUTCH DISC ASSEMBLY | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
| *a | Heavy object exceeding the capacity of the engine lifter |
Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.
If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.
| *a | High temperature areas |
Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.
Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
|
|
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
28800
5.REMOVE BATTERY
6.REMOVE FRONT WHEELS
51410
7.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
51442C
8.REMOVE ENGINE UNDER COVER LH
51441C
9.REMOVE ENGINE UNDER COVER RH
51447D
10.REMOVE CENTER NO. 4 ENGINE UNDER COVER
14.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
15.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55734A
16.REMOVE WATER GUARD PLATE RH (for LHD)
55735A
17.REMOVE WATER GUARD PLATE LH (for RHD)
55815E
18.REMOVE NO. 1 FRONT VENTILATOR SEAL (for LHD)
55815E
19.REMOVE NO. 1 FRONT VENTILATOR SEAL (for RHD)
55701J
20.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
21.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
17705
22.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
17801
23.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
24.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
74404A
26.REMOVE BATTERY CLAMP SUB-ASSEMBLY
82662A
27.REMOVE NO. 1 RELAY BLOCK COVER
28.DISCONNECT WIRE HARNESS
16571C
29.DISCONNECT NO. 1 RADIATOR HOSE
16572D
30.DISCONNECT NO. 2 RADIATOR HOSE
33820B
32.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
23826
34.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
77261D
35.DISCONNECT FUEL TANK TO CANISTER TUBE
16290F
36.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY
87245
37.DISCONNECT INLET HEATER WATER HOSE
23901
38.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp for the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
88711
39.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
88704
40.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
45259A
42.REMOVE COLUMN HOLE COVER SILENCER SHEET
45.REMOVE FRONT DRIVE SHAFT ASSEMBLY
for TMMF Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY (for M15A-FKS TMMF Made)>REMOVAL
11361J
46.REMOVE FLYWHEEL HOUSING UNDER COVER (for CVT)
31418
48.DISCONNECT NO. 1 CLUTCH HOSE (for Manual Transaxle)
Using a 10 mm union nut wrench, disconnect the bleeder clutch release tube from the No. 1 clutch hose.
Remove the clip and disconnect the No. 1 clutch hose from the clutch flexible hose bracket.
49.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
| *A | for CVT | *B | for Manual Transaxle |
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
for CVT:
Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.
for Manual Transaxle:
Remove the 4 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.
Remove the 10 bolts to separate the front suspension crossmember sub-assembly from the vehicle.
1. Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
12353
50.REMOVE ENGINE MOUNTING BRACKET CAP
Turn over the engine mounting bracket cap to the upper part.
While rotating in the direction shown in the diagram, remove the engine mounting bracket cap.
51.INSTALL ENGINE HANGERS
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 91552-F1040 |
1. Using an engine sling device and engine lift, secure the engine assembly with transaxle.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
12372A
52.REMOVE ENGINE MOUNTING INSULATOR LH
|
|
12305
53.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
|
|
54.REMOVE WATER HOSE (for CVT)
55.REMOVE WATER HOSE (for Manual Transaxle)
28100
56.REMOVE STARTER ASSEMBLY
11363A
57.REMOVE FLYWHEEL HOUSING SIDE COVER
82121
58.REMOVE ENGINE WIRE
| *A | for CVT | *B | for Manual Transaxle |
30400
60.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)
19315
64.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
16620D
66.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
27020
67.REMOVE GENERATOR WITH REGULATOR ASSEMBLY
for 80A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 80A Type)>REMOVAL
for 100A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 100A Type)>REMOVAL
69.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
70.REMOVE ENGINE HANGERS