Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR (for Sensor 1) › from 2021.07
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442028 AIR FUEL RATIO SENSOR(for Sensor 1) A

M15A-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR(for Sensor 1)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A485869N01
0.167,1.5 7,4.583 6.833,3.083 4.25,0.75 4.583,0.75 false 5.844,2.25 6.177,2.25 false 6.042,2.875 6.375,2.875 false 5.333,3.771 5.333,4.104 false 1.917,2.833 1.917,3.167 false 1.5,3.708 1.5,4.042 false 1.271,2.083 1.604,2.083 false 3.5,1.5 3.5,4.583 false 4.615,0.604 4.896,0.958 0.281,0.354 18 false 1 1.667,1.896 1.948,2.25 0.281,0.354 18 false 2 1.844,3.188 2.125,3.542 0.281,0.354 18 false 4 1.438,4.063 1.719,4.417 0.281,0.354 18 false 6 5.281,4.135 5.563,4.49 0.281,0.354 18 false 7 5.844,2.719 6.125,3.073 0.281,0.354 18 false 5 6.24,2.073 6.521,2.427 0.281,0.354 18 false 3 3.552,1.542 3.865,1.813 0.313,0.271 12 false *B 0.271,1.542 0.583,1.813 0.313,0.271 12 false *A 4.323,2.573 4.677,2.76 0.354,0.188 10 false x12 0.604,2.552 0.958,2.74 0.354,0.188 10 false x11

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WINDSHIELD WIPER MOTOR AND LINK - - - -
2 WATER GUARD PLATE RH 55734A - - -
3 WATER GUARD PLATE LH 55735A - - -
4 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
5 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
6 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
7 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -

*A for LHD *B for RHD

A485871N01
1.667,1.76 2.083,1.76 false 2.49,1.625 2.771,1.958 0.281,0.333 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

8 AIR FUEL RATIO SENSOR 89467B (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air fuel ratio sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
·

Replacement of air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold.

·

Touching high-temperature areas such as the engine and exhaust manifold could result in burns.



PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55734A 2.REMOVE WATER GUARD PLATE RH (for LHD)

Hide 55735A 3.REMOVE WATER GUARD PLATE LH (for RHD)

Hide 55815E 4.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 5.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 89467B 8.REMOVE AIR FUEL RATIO SENSOR

a.
A458737N01
2.896,1.313 3.24,0.99 true 0.49,0.115 3.24,0.469 2.75,0.354 18 false i, ii, iii 2.74,1.323 3.031,1.521 0.292,0.198 10 true SST

i.

Disconnect the air fuel ratio sensor connector.


ii.

Disengage the 2 clamps.


iii.

Using SST, remove the air fuel ratio sensor from the exhaust manifold.

SST
09224-00012  

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.