Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2021.07
RM3700E _51 Engine / Hybrid System _105429 STOP AND START _0482038 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P30DF62  Backup Boost Converter Circuit Board(Thermistor) Signal Compare Failure  P30EF4B  Backup Boost Converter Circuit Board Over Temperature  P323A00  Backup Boost Converter "A"  P323A16  Backup Boost Converter "A" Circuit Voltage Below Threshold  P323AA2  Backup Boost Converter "A" System Voltage Low  P323B29  Backup Boost Converter "A" Control Circuit Signal Invalid  P323B38  Backup Boost Converter "A" Control Circuit Signal Cycle Invalid  


DESCRIPTION

Refer to DTC P323A19.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>P323A19

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory DTC Output from Priority Note
P30DF62 Backup Boost Converter Circuit Board(Thermistor) Signal Compare Failure The following conditions is met for 1 second or more (1 trip detection logic):
·

Difference in temperature between thermistor 1 and thermistor 2 of the engine stop and start ECU is 40°C (72°F) or higher.


·

Wire harness or connector

·

Auxiliary battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Engine stop and start ECU


Blinks DTC stored Stop and Start A SAE Code: P30DF
P30EF4B Backup Boost Converter Circuit Board Over Temperature The following conditions is met for 1 second or more (1 trip detection logic):
·

Engine stop and start ECU thermistor temperature is 135°C (275°F) or higher.


·

Wire harness or connector

·

Auxiliary battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Engine stop and start ECU


Blinks DTC stored Stop and Start A SAE Code: P30EF
P323A00 Backup Boost Converter "A" The following conditions is met for 1 second or more (1 trip detection logic):
·

Backup boost converter malfunction is detected.


·

Wire harness or connector

·

Auxiliary battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Engine stop and start ECU


Blinks DTC stored Stop and Start A SAE Code: P323A
P323A16 Backup Boost Converter "A" Circuit Voltage Below Threshold One of the following conditions is met for 2 second or more (1 trip detection logic):
·

IG41 voltage is 6.0 V or less and backup boost converter output overcurrent is not detected.

·

B41, B42 or B43 voltage is 6.0 V or less, backup boost converter is not overheating and backup boost converter output overcurrent is not detected.


·

Wire harness or connector

·

Auxiliary battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Engine stop and start ECU


Blinks DTC stored Stop and Start A SAE Code: P323A
P323AA2 Backup Boost Converter "A" System Voltage Low The following conditions is met for 1 second or more (1 trip detection logic):
·

Backup boost converter malfunction is detected.


·

Wire harness or connector

·

Auxiliary battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Engine stop and start ECU


Blinks DTC stored Stop and Start A SAE Code: P323A
P323B29 Backup Boost Converter "A" Control Circuit Signal Invalid The following conditions is met for 1 second or more (1 trip detection logic):
·

Backup boost converter malfunction is detected.


·

Wire harness or connector

·

Auxiliary battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Engine stop and start ECU


Blinks DTC stored Stop and Start A SAE Code: P323C
P323B38 Backup Boost Converter "A" Control Circuit Signal Cycle Invalid The following conditions is met for 1 second or more (1 trip detection logic):
·

Backup boost converter malfunction is detected.


·

Wire harness or connector

·

Auxiliary battery

·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Engine stop and start ECU


Blinks DTC stored Stop and Start A SAE Code: P323C

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the auxiliary battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Auxiliary battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the auxiliary battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of auxiliary battery Charge Control cannot be checked, charge the auxiliary battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

b.

Start the engine and warm it up.


c.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Keep the engine stopped by stop and start control for 1 second or more.


f.

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the auxiliary battery voltage is low.



g.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392


STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

For wire harness and connector inspection procedures and precautions, refer to "General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE"

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC NO.1 FUSE AND BBC NO. 2 FUSE)

Pre-procedure1

a.

Disconnect the A66 engine stop and start ECU connector.


b.

Remove the BBC NO. 1 fuse and BBC NO. 2 fuse from the No. 1 engine room relay block.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A66)Location & Routing

Click Connector(A66)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

A66-1 (BIN2) - 2 (BBC NO. 2 fuse holder) Always Below 1 Ω
A66-3 (BIN1) - 2 (BBC NO. 1 fuse holder) Always Below 1 Ω
A66-1 (BIN2) - Body ground and other terminals Always 10 kΩ or higher
2 (BBC NO. 2 fuse holder) - Body ground and other terminals Always 10 kΩ or higher
A66-3 (BIN1) - Body ground and other terminals Always 10 kΩ or higher
2 (BBC NO. 1 fuse holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Disconnect the A66 and H43 engine stop and start ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A66)Location & Routing

Click Connector(A66)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

A66-1 (BIN2) - Body ground Always 9.5 to 14 V
A66-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ON.


Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H43)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

H43-18 (IGP) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

e.

None.



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

Pre-procedure1

a.

Disconnect the A66 and A67 engine stop and start ECU connectors.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A66,A67)Location & Routing

Click Connector(A66)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

A66-8 (GND1) - Body ground Always 9.5 to 14 V
A66-2 (GND2) - Body ground Always 9.5 to 14 V
A67-6 (DGND) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H6 combination meter assembly connector.


c.

Disconnect the H1 power steering ECU with motor assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H6,H1)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

Click Connector(H1)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assembly

H43-10 (IG12) - H6-38 (IG+) Always Below 1 Ω
H43-23 (IG31) - H1-1 (IG) Always Below 1 Ω
H43-10 (IG12) - Body ground and other terminals Always 10 kΩ or higher
H43-23 (IG31) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

e.

None.



OK

5.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

18.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O34 door control and tire pressure monitoring system receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O34)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O34)Body>Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key and Tire Pressure Monitoring System Receiver Assembly)

H43-2 (B41) - O34-7 (+B) Always Below 1 Ω
H43-2 (B41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

7.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

41.CHECK VEHICLE SPECIFICATION
8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H82 navigation ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H82)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H82)Instrument Panel>Instrument Panel Wire / Speaker Wire>Navigation ECU

H43-11 (B43) - H82-10 (+B) Always Below 1 Ω
H43-11 (B43) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

9.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H79 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H79)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H43-12 (B42) - H79-4 (+B1) Always Below 1 Ω
H43-12 (B42) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

10.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

11.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

27.CHECK VEHICLE SPECIFICATION
11.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H61 meter mirror sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H61)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assembly

H43-11 (B43) - H61-2(B) Always Below 1 Ω
H43-11 (B43) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

12.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
for Automatic Air Conditioning System A
for Manual Air Conditioning System B



A

13.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

21.CHECK VEHICLE SPECIFICATION
13.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H31 air conditioning control assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H31)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H31)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Control Assembly

H43-3 (IG41) - H31-9 (IG+) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

14.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

15.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

19.CHECK VEHICLE SPECIFICATION
15.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

16.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

17.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

17.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O33 door control and tire pressure monitoring system receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O33)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O33)Body>Floor Wire>Tire Pressure Warning ECU and Receiver (Door Control and Tire Pressure Monitoring System Receiver Assembly)

H43-2 (B41) - O33-7 (+B) Always Below 1 Ω
H43-2 (B41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

7.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

20.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

20.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

22.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

25.CHECK VEHICLE SPECIFICATION
22.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

23.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

24.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

24.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

26.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

26.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
for Automatic Air Conditioning System A
for Manual Air Conditioning System B



A

28.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

35.CHECK VEHICLE SPECIFICATION
28.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H31 air conditioning control assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H31)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H31)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Control Assembly

H43-3 (IG41) - H31-9 (IG+) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

29.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

30.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

33.CHECK VEHICLE SPECIFICATION
30.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

31.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

32.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

32.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

34.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

34.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

36.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

39.CHECK VEHICLE SPECIFICATION
36.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

37.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

38.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

38.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

40.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

40.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Radio and Display Receiver Assembly A
w/o Radio and Display Receiver Assembly B



A

42.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

73.CHECK VEHICLE SPECIFICATION
42.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H79 radio and display receiver assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H79)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H43-12 (B42) - H79-4 (+B1) Always Below 1 Ω
H43-26 (AC42) - H79-15 (ACC1) Always Below 1 Ω
H43-12 (B42) - Body ground and other terminals Always 10 kΩ or higher
H43-26 (AC42) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

43.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

43.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

44.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

59.CHECK VEHICLE SPECIFICATION
44.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H61 meter mirror sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H61)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assembly

H43-11 (B43) - H61-2(B) Always Below 1 Ω
H43-11 (B43) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

45.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
for Automatic Air Conditioning System A
for Manual Air Conditioning System B



A

46.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

53.CHECK VEHICLE SPECIFICATION
46.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H31 air conditioning control assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H31)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H31)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Control Assembly

H43-3 (IG41) - H31-9 (IG+) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

47.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

47.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

48.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

51.CHECK VEHICLE SPECIFICATION
48.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

49.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

49.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

50.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

50.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

51.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

52.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

52.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

53.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

54.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

57.CHECK VEHICLE SPECIFICATION
54.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

55.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

56.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

56.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

57.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

58.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

58.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

59.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
for Automatic Air Conditioning System A
for Manual Air Conditioning System B



A

60.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

67.CHECK VEHICLE SPECIFICATION
60.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H31 air conditioning control assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H31)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H31)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Control Assembly

H43-3 (IG41) - H31-9 (IG+) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

61.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

61.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

62.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

65.CHECK VEHICLE SPECIFICATION
62.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

63.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

63.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

64.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

64.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

65.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

66.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

66.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

67.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

68.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

71.CHECK VEHICLE SPECIFICATION
68.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

69.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

69.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

70.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

70.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

71.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

72.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

72.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

73.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

74.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

89.CHECK VEHICLE SPECIFICATION
74.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H61 meter mirror sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H61)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assembly

H43-11 (B43) - H61-2(B) Always Below 1 Ω
H43-11 (B43) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

75.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

75.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
for Automatic Air Conditioning System A
for Manual Air Conditioning System B



A

76.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

83.CHECK VEHICLE SPECIFICATION
76.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H31 air conditioning control assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H31)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H31)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Control Assembly

H43-3 (IG41) - H31-9 (IG+) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

77.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

77.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

78.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

81.CHECK VEHICLE SPECIFICATION
78.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

79.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

79.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

80.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

80.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

81.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

82.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

82.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

83.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

84.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

87.CHECK VEHICLE SPECIFICATION
84.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

85.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

85.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

86.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

86.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

87.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

88.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

88.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

89.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
for Automatic Air Conditioning System A
for Manual Air Conditioning System B



A

90.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

97.CHECK VEHICLE SPECIFICATION
90.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H31 air conditioning control assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,H31)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(H31)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Control Assembly

H43-3 (IG41) - H31-9 (IG+) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

91.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

91.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

92.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

95.CHECK VEHICLE SPECIFICATION
92.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

93.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

93.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

94.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

94.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

95.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

96.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

96.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

97.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

98.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

101.CHECK VEHICLE SPECIFICATION
98.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,B8)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

99.CHECK VEHICLE SPECIFICATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

99.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

100.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

100.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

101.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification


Result:
Result Proceed to
w/ Clearance Sonar System A
w/o Clearance Sonar System B



A

102.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

B

102.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

Pre-procedure1

a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the O60 clearance warning ECU assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H43,O60)Location & Routing

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR