The condition of the windshield wiper switch assembly is detected and sent to the steering sensor in this circuit.
for TMMF Made
for TMC Made
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1
*1: w/ Entry and Start System
Read the Data List according to the display on the GTS.
Refer to Inspection for each position of the switch.
Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>INSPECTION
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper OFF Switch | Front wiper switch OFF position signal | OFF or ON | OFF: Front wiper switch not in OFF position
ON: Front wiper switch in OFF position |
- |
| Wiper Auto/Int Switch | Front wiper switch INT position signal | OFF or ON | OFF: Front wiper switch not in INT position
ON: Front wiper switch in INT position |
- |
| Wiper Lo Switch | Front wiper switch LO position signal | OFF or ON | OFF: Front wiper switch not in LO position
ON: Front wiper switch in LO position |
- |
| Wiper Hi Switch | Front wiper switch HI position signal | OFF or ON | OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position |
- |
| Wiper Mist Switch | Front wiper switch MIST position signal | OFF or ON | OFF: Front wiper switch not in MIST position
ON: Front wiper switch in MIST position |
- |
| Washer Switch | Washer switch Fr WASH position signal | OFF or ON | OFF: Washer switch not in Fr WASH position
ON: Washer switch in Fr WASH position |
- |
| Rear Wiper INT Switch | Rear wiper switch Rr INT position signal | OFF or ON | OFF: Rear wiper switch not in Rr ON position
ON: Rear wiper switch in Rr ON position |
- |
| Rear Wiper ON Switch | Rear wiper switch Rr ON position signal | OFF or ON | OFF: Rear wiper switch not in Rr ON position
ON: Rear wiper switch in Rr ON position |
- |
| Rear Washer Switch | Washer switch Rr WASH position signal | OFF or ON | OFF: Washer switch not in Rr WASH position
ON: Washer switch in Rr WASH position |
- |
| Tester Display |
|---|
| Wiper OFF Switch |
| Wiper Auto/Int Switch |
| Wiper Lo Switch |
| Wiper Hi Switch |
| Wiper Mist Switch |
| Washer Switch |
| Rear Wiper INT Switch |
| Rear Wiper ON Switch |
| Rear Washer Switch |
The GTS display changes correctly in response to the windshield wiper switch assembly operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
OK
NG
Disconnect the A49 windshield wiper relay Assembly connector.
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H39,A49,H4)Location & Routingewd_type=routing;type=c,c,c;code=H39,A49,H4 Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H39;pinno=2 Click Connector(A49)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assemblyewd_type=component;type=c;code=A49;pinno=3 Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H4;pinno=12 |
||
| H39-2 (2S) - A49-3 (2S) | Always | Below 1 Ω |
| H39-2 (2S) or A49-3 (2S) - Body ground | Always | 10 kΩ or higher |
| H39-2 (2S) - H4-12 (WHI) | Always | Below 1 Ω |
| H39-2 (2S) or H4-12 (WHI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the A49 windshield wiper relay assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H39)Location & Routingewd_type=routing;type=c;code=H39 Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H39;pinno=2 |
||
| H39-2 (2S) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU (for LHD)>REMOVAL
for RHD: Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU (for RHD)>REMOVAL
Disconnect the A49 windshield wiper relay assembly connector.
Connect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H39)Location & Routingewd_type=routing;type=c;code=H39 Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assemblyewd_type=component;type=c;code=H39;pinno=2 |
||
| H39-2 (2S) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL