Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0445205 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Check Bus 2 Line  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen.
·

CAN main bus line, CAN branch line or connector

·

Central gateway ECU (network gateway ECU)

·

Engine stop and start ECU

(w/ Stop and Start System)

·

TCM

(for CVT)

·

ECM

·

No. 6 global CAN junction connector



WIRING DIAGRAM

C434484E02
1.385,1.031 2,1.229 0.615,0.198 10 false CA4H 1.406,1.563 2.021,1.76 0.615,0.198 10 false CA4L 1.896,1.031 2.51,1.229 0.615,0.198 10 false 26 1.885,1.573 2.5,1.771 0.615,0.198 10 false 25 5.458,1.135 6.073,1.333 0.615,0.198 10 false CANH 5.458,1.656 6.073,1.854 0.615,0.198 10 false CANL 2.792,1.563 3.406,1.76 0.615,0.198 10 false 14 2.854,1 3.469,1.198 0.615,0.198 10 false 3 4.177,1.563 4.573,1.74 0.396,0.177 10 false 13 4.198,1.021 4.677,1.219 0.479,0.198 10 false 2 4.208,3.146 4.646,3.323 0.438,0.177 10 false 1 4.167,3.688 4.615,3.896 0.448,0.208 10 false 12 2.844,4.26 3.458,4.458 0.615,0.198 10 false H117 2.833,4.458 4.521,4.906 1.688,0.448 10 false No. 6 Global CAN Junction Connector 0.479,2.219 2.458,2.625 1.979,0.406 10 false Central Gateway ECU (Network Gateway ECU) 0.49,2.042 0.854,2.302 0.365,0.26 10 false H40 5.177,1.021 5.573,1.198 0.396,0.177 10 false 13 5.177,1.573 5.573,1.75 0.396,0.177 10 false 14 5,2.052 5.615,2.25 0.615,0.198 10 false H43 5.01,2.219 7.031,2.49 2.021,0.271 10 false Engine Stop and Start ECU*1 5.115,3.698 5.51,3.875 0.396,0.177 10 false 18 5.208,3.177 5.604,3.354 0.396,0.177 10 false 8 5.427,3.698 6.042,3.896 0.615,0.198 10 false CANL 5.417,3.198 6.031,3.396 0.615,0.198 10 false CANH 5.656,4.198 6.271,4.396 0.615,0.198 10 false A54 5.656,4.375 6.677,5.031 1.021,0.656 10 false ECM 1.333,3.771 1.948,3.969 0.615,0.198 10 false CANL 1.292,3.26 1.906,3.458 0.615,0.198 10 false CANH 1.844,3.688 2.458,3.885 0.615,0.198 10 false 16 1.833,3.167 2.448,3.365 0.615,0.198 10 false 15 2.792,3.698 3.406,3.896 0.615,0.198 10 false 15 2.865,3.156 3.479,3.354 0.615,0.198 10 false 4 0.813,4.208 1.427,4.406 0.615,0.198 10 false D71 0.802,4.396 1.417,4.594 0.615,0.198 10 false TCM*2 0.26,5.385 2.677,5.625 2.417,0.24 10 false *2: for CVT 0.25,4.927 2.667,5.167 2.417,0.24 10 false *1: w/ Stop and Start System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C425195C69
1.51,0.073 1.927,0.323 0.417,0.25 2.094,0.885 2.708,1.688 true 2,0.896 2.552,1.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.125 2.063,0.323 0.458,0.198 10 false H40 2.583,1.906 3.052,2.125 0.469,0.219 10 false CA4H 2.719,1.698 3.198,1.865 0.479,0.167 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES

NG

35.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR SHORT IN CAN BUS LINES
a.
C425195C69
1.51,0.073 1.927,0.323 0.417,0.25 2.094,0.885 2.708,1.688 true 2,0.896 2.552,1.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.125 2.063,0.323 0.458,0.198 10 false H40 2.583,1.906 3.052,2.125 0.469,0.219 10 false CA4H 2.719,1.698 3.198,1.865 0.479,0.167 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Result
OK
NG



OK

3.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

25.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C47
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.292 5.729,0.563 0.417,0.271 6.302,1.615 6.573,2.021 true 2.479,1.313 3,2.115 true 2.396,1.302 2.865,2.344 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 3.042,2.073 3.594,2.271 0.552,0.198 10 false CA4L 6.604,1.99 7.156,2.188 0.552,0.198 10 false BAT 2.885,2.344 3.438,2.542 0.552,0.198 10 false CA4H 5.438,0.354 5.75,0.552 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-26 (CA4H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-25 (CA4L) - H3-16 (BAT)



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

15.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
4.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C48
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.125 5.729,0.396 0.417,0.271 5.427,1.042 6.042,0.604 true 2.479,1.292 3.042,2.073 true 2.406,1.292 2.927,2.396 true 4.073,0.094 4.385,0.292 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 3.094,2.031 3.646,2.229 0.552,0.198 10 false CA4L 6.083,0.51 6.635,0.708 0.552,0.198 10 false CG 2.948,2.365 3.5,2.563 0.552,0.198 10 false CA4H 5.427,0.177 5.74,0.375 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-26 (CA4H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-25 (CA4L) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H117-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

6.CHECK VEHICLE TYPE

NG

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
6.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

B

8.CHECK VEHICLE TYPE
7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Engine Stop and Start ECU
H117-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

8.CHECK VEHICLE TYPE

NG

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
8.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for CVT A
except CVT B



A

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)

B

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to TCM
H117-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to ECM
H117-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H117-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Engine Stop and Start ECU
H117-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the D71 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to TCM
H117-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to ECM
H117-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

15.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H117-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

16.CHECK VEHICLE TYPE

NG

21.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
16.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

17.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

B

18.CHECK VEHICLE TYPE
17.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Engine Stop and Start ECU
H117-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

18.CHECK VEHICLE TYPE

NG

22.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
18.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for CVT A
except CVT B



A

19.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)

B

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
19.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to TCM
H117-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to ECM
H117-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
21.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H117-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

22.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Engine Stop and Start ECU
H117-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the D71 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to TCM
H117-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)

24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117,H3)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H117-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to ECM
H117-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

25.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-3 (CANH) - H117-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

26.CHECK VEHICLE TYPE

NG

31.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
26.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

27.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

B

28.CHECK VEHICLE TYPE
27.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-2 (CANH) - H117-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Engine Stop and Start ECU



Result:
Result
OK
NG



OK

28.CHECK VEHICLE TYPE

NG

32.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
28.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for CVT A
except CVT B



A

29.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)

B

30.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
29.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-4 (CANH) - H117-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to TCM



Result:
Result
OK
NG



OK

30.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

33.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
30.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-1 (CANH) - H117-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to ECM



Result:
Result
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

34.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
31.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-3 (CANH) - H117-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

32.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-2 (CANH) - H117-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Engine Stop and Start ECU



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ENGINE STOP AND START ECU)

33.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the D71 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-4 (CANH) - H117-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to TCM



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - TCM)

34.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-1 (CANH) - H117-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to ECM



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

35.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-26 (CA4H) - H40-25 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 6 Global CAN Junction Connector



Result:
Result
OK
NG



OK

NG

36.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
36.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H117 No. 6 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-3 (CANH) - H117-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

37.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

37.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 6 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H117)Location & Routing

Click Connector(H117)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 6 Global CAN Junction Connector

H117-1 (CANH) - H117-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to ECM



Result:
Result
OK
NG



OK

REPLACE NO. 6 GLOBAL CAN JUNCTION CONNECTOR

NG

38.CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM)
38.CHECK FOR OPEN IN CAN MAIN BUS LINES (ECM)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(A54)Location & Routing

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

A54-8 (CANH) - A54-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to No. 6 Global CAN Junction Connector



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - NO. 6 GLOBAL CAN JUNCTION CONNECTOR)