Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › CLEARANCE WARNING BUZZER (for RHD) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0483097 CLEARANCE WARNING BUZZER(for RHD) A

PARK ASSIST / MONITORING  CLEARANCE WARNING BUZZER(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B579426N01
1.354,3.729 1.688,3.729 false 3.24,3.625 3.573,3.625 false 5.25,2.448 5.25,2.781 false 6.531,0.188 6.865,0.188 false 6.583,0.604 6.823,0.604 false 1.135,3.594 1.417,3.948 0.281,0.354 18 false 5 3.635,3.469 3.917,3.823 0.281,0.354 18 false 4 3.771,4.01 4.083,4.208 0.313,0.198 10 false x2 5.188,2.792 5.469,3.146 0.281,0.354 18 false 3 6.323,0.021 6.604,0.375 0.281,0.354 18 false 1 6.375,0.448 6.656,0.802 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY 55480D - - -
4 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY RH - - - -
5 NO. 1 CLEARANCE WARNING BUZZER - - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No.1 clearance warning buzzer removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55480D 3.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 4.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY RH

a.
E433357


Hide 89343C 5.REMOVE NO. 1 CLEARANCE WARNING BUZZER

a.
B579428