Home › Engine / Hybrid System › M15A-FXE (EMISSION CONTROL) › CANISTER (for No. 1) › from 2021.07
RM3700E _51 Engine / Hybrid System _093307 M15A-FXE EMISSION CONTROL _0483242 CANISTER(for No. 1) A

M15A-FXE EMISSION CONTROL  CANISTER(for No. 1)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A459924N02
0.813,2.198 0.479,2.198 false 6.302,3.052 5.885,3.052 false 4,2.969 3.833,2.969 3.833,2.969 3.667,3.25 false 4.813,3.479 4.479,3.479 false 2.99,0.635 3.323,0.635 false 2.938,2.302 3,2.667 3,2.667 3.167,2.667 false 2.917,2.917 2.75,2.917 2.75,2.917 2.594,3.156 false 2.823,1.833 2.656,1.833 2.656,1.833 2.448,2.26 false 2.219,2.073 2.052,2.073 2.052,2.073 1.896,2.5 false 2.417,2.833 2.25,2.833 2.25,2.833 2.052,3.021 false 4.188,0.917 4.521,0.917 false 2.271,2.01 2.427,2.208 0.156,0.198 10 false ● 3,2.854 3.156,3.052 0.156,0.198 10 false ● 2.823,0.49 3.104,0.844 0.281,0.354 18 false 1 0.885,2.063 1.167,2.417 0.281,0.354 18 false 4 4.885,3.365 5.167,3.719 0.281,0.354 18 false 5 6.667,2.917 6.948,3.271 0.281,0.354 18 false 2 3.219,2.531 3.5,2.885 0.281,0.354 18 false 7 4.073,2.833 4.354,3.188 0.281,0.354 18 false 6 2.479,2.698 2.76,3.052 0.281,0.354 18 false 3 2.875,1.677 3.156,2.031 0.281,0.354 18 false 8 4.563,0.844 4.875,1.042 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY 77020A - - -
2 FUEL SENDER GAGE ASSEMBLY 83320 (Click here) - -
3 SUB-ASSEMBLY SUPPORT - - - -
4 FUEL PUMP HARNESS 77785 - - -
5 NO. 1 CAP - - - -
6 FUEL PUMP ASSEMBLY WITH MOTOR AND BRACKET 23210A - - -
7 NO. 2 FUEL SUCTION SUPPORT - - - -
8 FUEL MAIN VALVE ASSEMBLY 23070 - - -

*1 CANISTER (FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY) - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (fuel suction plate sub-assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Replacement of fuel pump Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 83320 2.REMOVE FUEL SENDER GAGE ASSEMBLY

Z101186

Click here(Click here)

Hide 3.REMOVE SUB-ASSEMBLY SUPPORT

Hide 77785 4.REMOVE FUEL PUMP HARNESS

Hide 23210A 6.REMOVE FUEL PUMP ASSEMBLY WITH MOTOR AND BRACKET

Hide 7.REMOVE NO. 2 FUEL SUCTION SUPPORT

Hide 23070 8.REMOVE FUEL MAIN VALVE ASSEMBLY