Home › Engine / Hybrid System › M15A-FXE (EMISSION CONTROL) › CANISTER (for No. 2) › from 2021.07
RM3700E _51 Engine / Hybrid System _093307 M15A-FXE EMISSION CONTROL _0483243 CANISTER(for No. 2) A

M15A-FXE EMISSION CONTROL  CANISTER(for No. 2)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A491837N01
0.583,3.583 3.167,5.583 2.583,2 3.167,3.583 5,5.583 1.833,2 5,3 7,5 2,2 2.26,4 2.594,4 false 2.167,5.083 2.5,5.083 false 3.917,4.281 4.083,4 4.083,4 4.25,4 false 5.417,3.854 5.417,4.188 false 4.302,2.667 4.635,2.667 false 5.75,2.469 6.083,2.469 false 4.771,1.917 5.104,1.917 false 5.521,1.625 5.854,1.625 false 4.781,1.25 5.115,1.25 false 4.146,0.333 4.479,0.333 false 0.583,4.583 3.167,4.583 false 3.948,0.167 4.229,0.521 0.281,0.354 18 false 1 5.292,1.75 5.573,2.104 0.281,0.354 18 false 2 4.594,1.083 4.875,1.438 0.281,0.354 18 false 3 4.708,2.51 4.99,2.865 0.281,0.354 18 false 4 5.344,4.208 5.625,4.563 0.281,0.354 18 false 5 2.948,3.896 3.229,4.25 0.281,0.354 18 false 6 4.323,3.833 4.604,4.188 0.281,0.354 18 false 7 2.823,4.927 3.104,5.281 0.281,0.354 18 false 8 6.313,2.313 6.594,2.667 0.281,0.354 18 false 2 5.156,1.823 5.313,2.021 0.156,0.198 10 false ● 6.167,2.375 6.323,2.573 0.156,0.198 10 false ● 5.917,1.521 6.073,1.719 0.156,0.198 10 false ● 6.406,4.146 6.625,4.323 0.219,0.177 10 false x3 0.646,3.625 1.021,3.865 0.375,0.24 12 false *A 0.635,4.625 1.01,4.865 0.375,0.24 12 false *B 3.198,3.625 3.573,3.865 0.375,0.24 12 false *B 5.042,3.052 5.417,3.292 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BENCH TYPE REAR SEAT CUSHION ASSEMBLY - (Click here) - -
2 REAR SEAT CUSHION LOCK HOOK 72693 - - -
3 REAR FLOOR SERVICE HOLE COVER 58325E - - -
4 NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY 77701W - - -
5 NO. 1 REAR FLOOR BOARD 58415Q - - -
6 NO. 2 CHARCOAL CANISTER - (Click here) - -
7 REAR SUSPENSION MEMBER SUB-ASSEMBLY 51206A - - -
8 NO. 2 CHARCOAL CANISTER - (Click here) - -

*A for 2WD *B for AWD
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (fuel suction plate sub-assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Replacement of fuel pump Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 2.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 58325E 3.REMOVE REAR FLOOR SERVICE HOLE COVER

Hide 77701W 4.DISCONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

Hide 58415Q 5.REMOVE NO. 1 REAR FLOOR BOARD (for 2WD)

a.
A491838


Hide 6.REMOVE NO. 2 CHARCOAL CANISTER (for 2WD)

a.
A491839N01
0.385,0.052 0.563,0.365 0.177,0.313 18 true i 3.802,0.073 4.313,0.344 0.51,0.271 18 true ii, iii

i.

Disconnect the canister air tube from the No. 2 canister.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


ii.

Remove the nut.


iii.

Disengage the 3 clamps to remove the No. 2 charcoal canister.



Hide 51206A 7.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY (for AWD)

Hide 8.REMOVE NO. 2 CHARCOAL CANISTER (for AWD)

a.
A491840N02
0.385,0.01 0.656,0.292 0.271,0.281 18 true i 3.958,0.021 4.49,0.302 0.531,0.281 18 true ii, iii

i.

Disconnect the canister air tube from the No. 2 canister.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


ii.

Remove the nut.


iii.

Disengage the 4 clamps to remove the No. 2 charcoal canister.