Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER › from 2021.07
RM3700E _53 Suspension _093739 REAR SUSPENSION _0441863 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C449227N01
5.198,1.323 4.969,1.323 false 4.302,3.24 4.302,3.417 false 4.031,4.146 3.792,4.146 false 1.635,2.813 1.281,2.813 false 1.823,0.375 1.469,0.375 false 1.896,0.219 2.177,0.573 0.281,0.354 18 false 3 1.083,2.656 1.365,3.01 0.281,0.354 18 false 5 4.083,3.969 4.365,4.323 0.281,0.354 18 false 1 4.25,3.417 4.531,3.771 0.281,0.354 18 false 4 5.281,1.146 5.563,1.5 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY G1050 - - -
2 REAR UPPER CONTROL ARM ASSEMBLY LH 48790 - - -
3 REAR UPPER CONTROL ARM ASSEMBLY RH 48770A - - -
4 LOWER CONTROL ARM ASSEMBLY LH 48730 - - -
5 LOWER CONTROL ARM ASSEMBLY RH 48720 - - -

C444405N02
5.969,0.573 6.229,0.573 false 0.885,2.198 1.146,2.198 false 3.354,1.417 3.521,1.417 3.521,1.417 3.771,2.167 false 3.156,1.24 3.438,1.594 0.281,0.354 18 false 6 6.323,1.448 6.604,1.802 0.281,0.354 10 false x2 6.229,2.104 6.51,2.458 0.281,0.354 10 false x2 5.854,0.458 6.083,0.708 0.229,0.25 10 false ● 1.188,2.083 1.417,2.333 0.229,0.25 10 false ● 1.729,3.302 2.01,3.656 0.281,0.354 10 false x2 1.021,2.979 1.302,3.333 0.281,0.354 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

6 FRONT EXHAUST PIPE ASSEMBLY 17410 (Click here) - -

● Non-reusable part - -

C449228N01
2.167,1.25 2.479,1.25 false 5.531,4.813 5.865,4.813 false 1.75,3 1.917,2.75 1.917,2.75 2.083,2.75 false 1.875,1.073 2.427,1.427 0.552,0.354 18 false 9 2.167,2.583 2.719,2.938 0.552,0.354 18 false 7 5.938,4.646 7.063,5.042 1.125,0.396 18 false 8, 10 2.458,4.021 3.01,4.375 0.552,0.354 10 false x2 0.677,2.99 1.229,3.344 0.552,0.354 10 false x2 4.896,3.448 5.448,3.802 0.552,0.354 10 false x2 5.698,3.354 6.25,3.708 0.552,0.354 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

7 REAR STABILIZER BAR 48812 - - -
8 DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A - - -
9 REAR SUSPENSION MEMBER SUB-ASSEMBLY 51206A (Click here) - -
10 REMOVE NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Rear wheel alignment adjustment for TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for TMMF Made:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
w/ Advanced Park:

Advanced Park


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system w/o Advanced Park:
(Click here)
w/ Advanced Park:
(Click here)
w/ Advanced Park:

Advanced Park


(Click here)

HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide G1050 1.REMOVE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

Hide 48790 2.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 3.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 48730 4.REMOVE LOWER CONTROL ARM ASSEMBLY LH

Hide 48720 5.REMOVE LOWER CONTROL ARM ASSEMBLY RH

a.

Perform the same procedure as for the LH side.


Hide 17410 6.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Z101186

Click here(Click here)

Hide 48812 7.REMOVE REAR STABILIZER BAR

Hide 890C0A 8.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C443674


Hide 51206A 9.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

Z101186

NOTICE:

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



a.
C443675N01
0.875,0.052 1.031,0.333 0.156,0.281 18 true i 4.188,0.063 4.344,0.375 0.156,0.313 18 true ii

i.

Using a transmission jack and a wooden block, support the rear suspension member sub-assembly.


ii.

Remove the 2 bolts and 2 nuts.


iii.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.




Hide 890C0A 10.REMOVE NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C429424