Home › Engine / Hybrid System › M15A-FKS (FUEL) › FUEL PUMP (for High Pressure) › from 2021.07
RM3700E _51 Engine / Hybrid System _093308 M15A-FKS FUEL _0440424 FUEL PUMP(for High Pressure) A

M15A-FKS FUEL  FUEL PUMP(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A458654N02
3.167,1.563 3.5,1.563 false 3.083,3 3.417,3 false 3.365,1.135 3.698,1.135 false 3.083,1.917 3.417,1.917 false 3.25,2.417 3.583,2.417 false 4.552,3.083 4.885,3.083 false 6.167,4.25 6.167,3.917 false 1.771,1.083 2.104,1.083 false 1.417,2.333 1.583,2.333 1.583,2.333 1.917,2 false 6.5,0.229 6.833,0.229 false 6.438,0.708 6.771,0.708 false 6.104,2.948 6.438,2.948 false 3.167,0.458 3.479,0.656 0.313,0.198 10 false x2 3.583,1.5 3.896,1.698 0.313,0.198 10 false ● 3.479,2.927 3.792,3.125 0.313,0.198 10 false ● 6.042,0.083 6.677,0.417 0.635,0.333 18 false 1, 2 6.24,0.573 6.521,0.927 0.281,0.354 18 false 3 3.479,1.792 3.833,2.094 0.354,0.302 18 false 11 3.646,2.271 3.979,2.594 0.333,0.323 18 false 10 4.969,2.938 5.25,3.292 0.281,0.354 18 false 6 6.094,4.292 6.375,4.646 0.281,0.354 18 false 5 1.5,0.938 1.781,1.292 0.281,0.354 18 false 8 1.156,2.198 1.438,2.552 0.281,0.354 18 false 7 4.167,1 4.448,1.354 0.281,0.354 18 false 9 5.958,2.833 6.24,3.188 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
2 PRECAUTION - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 NO. 2 VENTILATION HOSE 12262 - - -
5 NO. 1 AIR CLEANER HOSE 17881 - - -
6 VACUUM TUBE CONNECTOR HOSE 44777 - - -
7 FUEL TUBE SUB-ASSEMBLY 23902 (Click here) - -
8 NO. 1 FUEL PIPE SUB-ASSEMBLY 23801P (Click here) - -
9 FUEL PUMP ASSEMBLY - (Click here) - -
10 FUEL PUMP FLANGE 23191 - - -
11 FUEL PUMP LIFTER ASSEMBLY 23470 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Fuel pump assembly (for high pressure side) Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 12262 4.DISCONNECT NO. 2 VENTILATION HOSE

Hide 17881 5.REMOVE NO. 1 AIR CLEANER HOSE

Hide 44777 6.REMOVE VACUUM TUBE CONNECTOR HOSE

a.
A458646


Hide 23902 7.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A458647N01
0.427,0.094 0.708,0.448 0.281,0.354 18 false i

i.

Disconnect the fuel tube sub-assembly from the fuel pump assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 23801P 8.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A474495N02
0.083,0.125 0.271,0.406 0.188,0.281 18 true i 2.417,0.104 2.604,0.385 0.188,0.281 18 true ii 4.896,0.125 5.125,0.406 0.229,0.281 18 true iii 1.063,2.083 1.281,2.365 0.219,0.281 18 true iv 3.75,2.042 3.938,2.323 0.188,0.281 18 true v

i.

Disconnect the ignition coil assembly connector.


ii.

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


iii.

Using an 8 mm socket wrench, remove the bolt.


iv.

Loosen the 2 bolts of the fuel pump assembly.


v.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.



Hide 9.REMOVE FUEL PUMP ASSEMBLY

Z101186

NOTICE:

When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.



a.
A458649E01
0.083,0.031 0.229,0.344 0.146,0.313 18 true i 2.573,0 2.802,0.271 0.229,0.271 18 true ii 4.885,0.042 5.115,0.313 0.229,0.271 18 true iii

i.

Disconnect the fuel pump assembly connector.


ii.

Remove the 2 bolts, fuel pump assembly and fuel pump flange from the cylinder head cover sub-assembly.


iii.

Remove the O-ring from the fuel pump assembly.



Hide 23191 10.REMOVE FUEL PUMP FLANGE

a.
A458650


Hide 23470 11.REMOVE FUEL PUMP LIFTER ASSEMBLY

a.
A458651