Refer to DTC C13807E.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C13807F | Stop Lamp Relay Actuator Stuck Off | When the voltage at the +BS terminal is between 10 V or more and the stop light control relay (stop light switch assembly) drive output (STPO) is on, a signal is not input to the STP terminal for 5 seconds or more. | ·
Wire harness or connector ·
Stop light switch assembly ·
Skid control ECU (brake actuator assembly) ·
Rear combination light assembly LH ·
Rear combination Light assembly RH ·
Center stop light assembly |
Brake/EPB | B |
Refer to DTC C13807E.
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.
When DTC P057111, P057112 and/or P057113 are output together with DTC C13807F, inspect and repair the trouble areas indicated by DTC P057111, P057112 and/or P057113 first.
P057111: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>P057111
P057112: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>P057112
P057113: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>P057113
Check that the stop lights come on when the brake pedal is depressed.
The stop lights illuminate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the GTS to perform the Active Test.
| Tester Display | Measurement Item | Control Range | Restrict Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Lamp Relay | Stop light control relay (Stop light switch assembly) | Relay OFF / ON | Vehicle condition: Vehicle stopped
|
- |
| Tester Display |
|---|
| Stop Lamp Relay |
According to the display on the GTS, perform the Active Test and check the operation of the stop lights.
Stop lights turn on in accordance with the Active Test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A39)Location & Routingewd_type=routing;type=c;code=A39 Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A39;pinno=43 |
||
| A39-43 (STP2) - Body ground | Brake pedal depressed | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMMF Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
NG
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63)Location & Routingewd_type=routing;type=c;code=A63 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=4 |
||
| A63-4 (ACC) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A39)Location & Routingewd_type=routing;type=c;code=A39 Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A39;pinno=33 |
||
| A39-33 (STPO) - Body ground | Brake pedal depressed | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMMF Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Check that the stop lights come on when the brake pedal is depressed.
The stop lights illuminate.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Rear Turn Signal Light Bulb Type) | B |
| NG (Rear Turn Signal Light LED Type) | C |
Post-procedure1
None
A
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMMF Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
B
C
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the O102 rear combination light assembly LH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O102)Location & Routingewd_type=routing;type=c;code=O102 Click Connector(O102)Body>Floor Wire>Rear Combination Light Assembly LHewd_type=component;type=c;code=O102;pinno=3 |
||
| O102-3 (B) - Body ground | Brake pedal depressed | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
Refer to "Left or right stop light does not illuminate" of problem symptoms table.
w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE
w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the O102 rear combination light assembly LH connector.
Disconnect the O104 rear combination light assembly RH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O104)Location & Routingewd_type=routing;type=c;code=O104 Click Connector(O104)Body>Floor Wire>Rear Combination Light Assembly RHewd_type=component;type=c;code=O104;pinno=3 |
||
| O104-3 (B) - Body ground | Brake pedal depressed | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
Refer to "Left or right stop light does not illuminate" of problem symptoms table.
w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE
w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the O102 rear combination light assembly LH connector.
Disconnect the O104 rear combination light assembly RH connector.
Disconnect the Q1 center stop light assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Q1)Location & Routingewd_type=routing;type=c;code=Q1 Click Connector(Q1)Body>Center Stop Light Cord Assembly>Center Stop Light Assemblyewd_type=component;type=c;code=Q1;pinno=2 |
||
| Q1-2 (B) - Body ground | Brake pedal depressed | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the O102 rear combination light assembly LH connector.
Disconnect the O104 rear combination light assembly RH connector.
Disconnect the Q1 center stop light assembly connector.
Disconnect the A63 stop light switch assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63,O102)Location & Routingewd_type=routing;type=c,c;code=A63,O102 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=1 Click Connector(O102)Body>Floor Wire>Rear Combination Light Assembly LHewd_type=component;type=c;code=O102;pinno=3 |
||
| A63-1 (OUT) - O102-3 (B) | Always | Below 1 Ω |
| A63-1 (OUT) or O102-3 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the O106 rear combination light assembly LH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O106)Location & Routingewd_type=routing;type=c;code=O106 Click Connector(O106)Body>Floor Wire>Rear Combination Light Assembly LHewd_type=component;type=c;code=O106;pinno=3 |
||
| O106-3 (B) - Body ground | Brake pedal depressed | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
Refer to "Left or right stop light does not illuminate" of problem symptoms table.
w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE
w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the O106 rear combination light assembly LH connector.
Disconnect the O109 rear combination light assembly RH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O109)Location & Routingewd_type=routing;type=c;code=O109 Click Connector(O109)Body>Floor Wire>Rear Combination Light Assembly RHewd_type=component;type=c;code=O109;pinno=3 |
||
| O109-3 (B) - Body ground | Brake pedal depressed | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
Refer to "Left or right stop light does not illuminate" of problem symptoms table.
w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE
w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the O106 rear combination light assembly LH connector.
Disconnect the O109 rear combination light assembly RH connector.
Disconnect the Q1 center stop light assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(Q1)Location & Routingewd_type=routing;type=c;code=Q1 Click Connector(Q1)Body>Center Stop Light Cord Assembly>Center Stop Light Assemblyewd_type=component;type=c;code=Q1;pinno=2 |
||
| Q1-2 (B) - Body ground | Brake pedal depressed | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the O106 rear combination light assembly LH connector.
Disconnect the O109 rear combination light assembly RH connector.
Disconnect the Q1 center stop light assembly connector.
Disconnect the A63 stop light switch assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63,O106)Location & Routingewd_type=routing;type=c,c;code=A63,O106 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=1 Click Connector(O106)Body>Floor Wire>Rear Combination Light Assembly LHewd_type=component;type=c;code=O106;pinno=3 |
||
| A63-1 (OUT) - O106-3 (B) | Always | Below 1 Ω |
| A63-1 (OUT) or O106-3 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG