The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, "Traction Control Turned Off" will be displayed on the multi-information display and the VSC OFF indicator light will come on.
w/o Advanced Park
w/ Advanced Park
After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| w/o Advanced | A |
| w/ Advanced | B |
A
B
Check the indicator light and mode condition on the GTS changes according to VSC OFF switch (combination switch assembly) operation.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| TRC(TRAC)/VSC OFF Mode | TRC/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) |
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode Not defined: Not defined VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| Tester Display |
|---|
| TRC(TRAC)/VSC OFF Mode |
| Switch Operation | Mode Condition Display | Multi-information Display ("Traction Control Turned Off") | VSC OFF Indicator Light |
|---|---|---|---|
| Not pressed | Normal mode (TRC(TRAC) ON/VSC ON) | Not displayed | Does not come on |
| Pressing the VSC OFF switch (combination switch assembly) | TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) | Displayed | Does not come on |
| Pressing and holding the VSC OFF switch (combination switch assembly) | VSC OFF mode (TRC(TRAC) OFF/VSC OFF) | Displayed | Comes on |
| Result | Proceed to |
|---|---|
| Indicator light and mode condition display do not change | A |
| Mode condition display is normal, but indicator light does not change | B |
| Indicator light and mode condition display are normal | C |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH (for Console Box Side)>INSPECTION
The VSC OFF switch (combination switch assembly) is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH (for Console Box Side)>REMOVAL
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the H18 VSC OFF switch (combination switch assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H18,A39)Location & Routingewd_type=routing;type=c,c;code=H18,A39 Click Connector(H18)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Switch Assemblyewd_type=component;type=c;code=H18;pinno=7,5 Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A39;pinno=38 |
||
| H18-7 (+) - A39-38 (CSW) | Always | Below 1 Ω |
| H18-7 (+) or A39-38 (CSW) - Body ground | Always | 10 kΩ or higher |
| H18-5 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMMF Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
NG
Check the indicator light and mode condition on the GTS changes according to VSC OFF switch operation.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| TRC(TRAC)/VSC OFF Mode | TRC/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) |
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode Not defined: Not defined VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| Tester Display |
|---|
| TRC(TRAC)/VSC OFF Mode |
| Switch Operation | Mode Condition Display | Multi-information Display ("Traction Control Turned Off") | VSC OFF Indicator Light |
|---|---|---|---|
| Not pressed | Normal mode (TRC(TRAC) ON/VSC ON) | Not displayed | Does not come on |
| Pressing the VSC OFF switch | TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) | Displayed | Does not come on |
| Pressing and holding the VSC OFF switch | VSC OFF mode (TRC(TRAC) OFF/VSC OFF) | Displayed | Comes on |
| Result | Proceed to |
|---|---|
| Indicator light and mode condition display do not change | A |
| Mode condition display is normal, but indicator light does not change | B |
| Indicator light and mode condition display are normal | C |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH (for Instrument Panel Side)>INSPECTION
The VSC OFF switch is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH (for Instrument Panel Side)>REMOVAL
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the H154 VSC OFF switch connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H154,A39)Location & Routingewd_type=routing;type=c,c;code=H154,A39 Click Connector(H154)Instrument Panel>Instrument Panel Wire / Speaker Wire>VSC Off Switchewd_type=component;type=c;code=H154;pinno=5,2 Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A39;pinno=38 |
||
| H154-5 (+) - A39-38 (CSW) | Always | Below 1 Ω |
| H154-5 (+) or A39-38 (CSW) - Body ground | Always | 10 kΩ or higher |
| H154-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMMF Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
NG