Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0483555 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMMF Made) J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMMF Made)  Electric Parking Brake does not Operate  


WIRING DIAGRAM

C395609E05
0.604,0.719 1.833,0.917 1.229,0.198 10 false ABS NO. 2 0.604,1.385 1.833,1.583 1.229,0.198 10 false ECU-IG1 NO.2 3,1.583 3.344,1.802 0.344,0.219 10 false A39 5.135,1.313 7.01,1.792 1.875,0.479 10 false Combination Meter Assembly 3,1.792 4.552,2.5 1.552,0.708 10 false Skid Control ECU (Brake Actuator Assembly) 2.958,0.521 4.188,0.719 1.229,0.198 10 false +BS 3,1.219 4.354,1.417 1.354,0.198 10 false IGR 2.698,0.417 3.073,0.635 0.375,0.219 10 false 30 2.698,1.115 3.073,1.333 0.375,0.219 10 false 36 1.917,3.417 4.552,3.604 2.635,0.188 10 false : CAN Communication Line 0.156,2.688 2.208,2.979 2.052,0.292 10 false Engine Stop and Start ECU 0.167,2.5 0.802,2.708 0.635,0.208 10 false H43 0.823,2.052 2.052,2.25 1.229,0.198 10 false IG31 1.219,1.917 1.594,2.135 0.375,0.219 10 false 23 2.104,1.094 2.479,1.313 0.375,0.219 10 false *2 2.104,1.885 2.479,2.104 0.375,0.219 10 false *1 4.75,2.417 6.823,2.625 2.073,0.208 10 false *1: w/ Stop and Start System 4.75,2.854 6.823,3.063 2.073,0.208 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned to ON.



HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light on the combination meter may be malfunctioning.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.VEHICLE OPERATION CHECK

B

2.VEHICLE OPERATION CHECK
a.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for TMMF Made 2WD)>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Lock and release operation is normal and parking brake indicator light turns off or blinks A
Lock and release operation is malfunctioning and parking brake indicator light illuminates or turns off according to switch operation B
Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks C



A

3.INSPECT COMBINATION METER ASSEMBLY

B

INSPECT REAR BRAKE

C

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
3.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Park Warning
50004 409 108

b.

Check the combination meter assembly.

OK:

Parking brake indicator light turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-30 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK VEHICLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

6.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

B

7.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)
6.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-36 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-36 (IGR) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ENGINE STOP AND START ECU)
8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ENGINE STOP AND START ECU)
a.

Turn the ignition switch off.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the H43 engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A39,H43)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECU

A39-36 (IGR) - H43-23 (IG31) Always Below 1 Ω
A39-36 (IGR) or H43-23 (IG31) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR