Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0483556 ELECTRIC PARKING BRAKE SYSTEM(for HV Model TMMF Made) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model TMMF Made)  C061013  Right Electric Parking Brake Actuator Control Circuit Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C061013 Right Electric Parking Brake Actuator Control Circuit Open
·

Diagnosis Condition:

Electric parking brake not operating

·

Malfunction Status:

The ECU power supply is normal but there is a malfunction in the electric parking brake actuator RH internal circuit (open).

·

Detection Time:

Approximately 1 second


·

Parking brake actuator assembly RH

·

No. 1 parking brake wire assembly

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


DTC stored Brake/EPB A An electric parking brake system malfunction is displayed on the multi-information display.

CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 4 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned to ON.



PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for 2WD A
for AWD B



A

2.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

B

5.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
2.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the uO3 and u1 No. 1 parking brake wire assembly connectors.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

C466752C02
1.802,0.208 2.219,0.458 0.417,0.25 5,0.25 5.417,0.5 0.417,0.25 5.833,2.167 5.417,1.667 true 4.583,2.167 5,1.667 true 1.906,0.26 2.365,0.458 0.458,0.198 10 false uO3 5.115,0.292 5.573,0.49 0.458,0.198 10 false u1 5.854,2.229 6.385,2.479 0.531,0.25 10 false MRR+ 4.344,2.219 4.865,2.417 0.521,0.198 10 false MRR- 1.969,2.438 2.427,2.646 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 5.146,2.385 5.604,2.583 0.458,0.198 10 false *c
*a Front view of No. 1 Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly RH) - -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO3,u1)Location & Routing

Click Connector(uO3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

Click Connector(u1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RH

uO3-1 - u1-2 (MRR+) Always Below 1 Ω
uO3-1 - Other terminals Always 10 kΩ or higher
uO3-2 - u1-1 (MRR-) Always Below 1 Ω
uO3-2 - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Make sure the No. 1 parking brake wire assembly is securely installed.


c.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the u1 parking brake actuator assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A39,u1)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(u1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RH

A39-2 (MRR+) - u1-2 (MRR+) Always Below 1 Ω
A39-3 (MRR-) - u1-1 (MRR-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH

5.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the uO1 and u1 No. 1 parking brake wire assembly connectors.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

C433186C11
1.948,0.313 2.365,0.563 0.417,0.25 5,0.25 5.417,0.5 0.417,0.25 5.833,2.167 5.417,1.667 true 4.583,2.167 5,1.667 true 2.031,0.354 2.49,0.552 0.458,0.198 10 false uO1 5.115,0.292 5.573,0.49 0.458,0.198 10 false u1 5.854,2.229 6.385,2.479 0.531,0.25 10 false MRR+ 4.344,2.219 4.865,2.417 0.521,0.198 10 false MRR- 2.156,2.167 2.615,2.375 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 5.146,2.385 5.604,2.583 0.458,0.198 10 false *c
*a Front view of No. 1 Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly RH) - -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO1,u1)Location & Routing

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

Click Connector(u1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RH

uO1-1 - u1-2 (MRR+) Always Below 1 Ω
uO1-1 - Other terminals Always 10 kΩ or higher
uO1-2 - u1-1 (MRR-) Always Below 1 Ω
uO1-2 - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Make sure the No. 1 parking brake wire assembly is securely installed.


c.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the u1 parking brake actuator assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A39,u1)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(u1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RH

A39-2 (MRR+) - u1-2 (MRR+) Always Below 1 Ω
A39-3 (MRR-) - u1-1 (MRR-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH