Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483557 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  C14E014  Left Front Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC C050012

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>C050012

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C14E014 Left Front Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open An open or short in the speed sensor power supply circuit is detected for 0.12 seconds or more.
·

Front speed sensor LH

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A22 front speed sensor LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A22)Location & Routing

Click Connector(A22)Engine Compartment>Engine Room Main Wire>Front Speed Sensor LH

A22-1 (FL+) - A22-2 (FL-) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

2.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A22 front speed sensor LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A22,A39)Location & Routing

Click Connector(A22)Engine Compartment>Engine Room Main Wire>Front Speed Sensor LH

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A22-1 (FL+) or A39-24 (FL+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR