Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483557 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  C13807F  Stop Lamp Relay Actuator Stuck Off  


DESCRIPTION

Refer to DTC C13807E.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>C13807E

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C13807F Stop Lamp Relay Actuator Stuck Off When the voltage at the +BS terminal is between 10 V or more and the stop light control relay (stop light switch assembly) drive output (STPO) is on, a signal is not input to the STP terminal for 5 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light assembly


Brake/EPB B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the details of the DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435
HINT:

When DTC P057111, P057112 and/or P057113 are output together with DTC C13807F, inspect and repair the trouble areas indicated by DTC P057111, P057112 and/or P057113 first.



Result:
Result Proceed to
C13807F and P057111, P057112, P057113 are output A
C13807F is output B



A

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

B

2.CHECK STOP LIGHT OPERATION
2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

NG

7.CHECK VEHICLE
3.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)
a.

According to the display on the GTS, perform the Active Test and check the operation of the stop lights.

Chassis > Brake/EPB > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
Stop Lamp Relay Stop light control relay (Stop light switch assembly) Relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


-
Chassis > Brake/EPB > Active Test
Tester Display
Stop Lamp Relay
50004 435 27
OK:

Stop lights turn on in accordance with the Active Test.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

NG

5.INSPECT STOP LIGHT SWITCH ASSEMBLY (ACC TERMINAL VOLTAGE)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-43 (STP2) - Body ground Brake pedal depressed 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STOP LIGHT SWITCH ASSEMBLY (ACC TERMINAL VOLTAGE)
a.
C440416C44
0.448,0.448 0.823,0.698 0.375,0.25 2.083,1.667 1.729,1.031 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.5,0.479 0.958,0.677 0.458,0.198 10 false A63 2.021,1.708 2.479,1.906 0.458,0.198 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-4 (ACC) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-33 (STPO) - Body ground Brake pedal depressed 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK VEHICLE
Result:
Result Proceed to
Rear Turn Signal Light Bulb Type A
Rear Turn Signal Light LED Type B



A

8.CHECK STOP LIGHT OPERATION

B

13.CHECK STOP LIGHT OPERATION
8.CHECK STOP LIGHT OPERATION

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the O102 rear combination light assembly LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O102)Location & Routing

Click Connector(O102)Body>Floor Wire>Rear Combination Light Assembly LH

O102-3 (B) - Body ground Brake pedal depressed 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY LH (STOP LIGHT CIRCUIT))

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE

w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE


NG

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the O102 rear combination light assembly LH connector.


c.

Disconnect the O104 rear combination light assembly RH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O104)Location & Routing

Click Connector(O104)Body>Floor Wire>Rear Combination Light Assembly RH

O104-3 (B) - Body ground Brake pedal depressed 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY RH (STOP LIGHT CIRCUIT))

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE

w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE


NG

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the O102 rear combination light assembly LH connector.


c.

Disconnect the O104 rear combination light assembly RH connector.


d.

Disconnect the Q1 center stop light assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Q1)Location & Routing

Click Connector(Q1)Body>Center Stop Light Cord Assembly>Center Stop Light Assembly

Q1-2 (B) - Body ground Brake pedal depressed 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

GO TO LIGHTING SYSTEM (CENTER STOP LIGHT ASSEMBLY (STOP LIGHT CIRCUIT))

Refer to "High mounted stop light does not illuminate" of problem symptoms table.

w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE

w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE


NG

12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the O102 rear combination light assembly LH connector.


c.

Disconnect the O104 rear combination light assembly RH connector.


d.

Disconnect the Q1 center stop light assembly connector.


e.

Disconnect the A63 stop light switch assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A63,O102)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

Click Connector(O102)Body>Floor Wire>Rear Combination Light Assembly LH

A63-1 (OUT) - O102-3 (B) Always Below 1 Ω
A63-1 (OUT) or O102-3 (B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK STOP LIGHT OPERATION

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

14.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
14.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the O106 rear combination light assembly LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O106)Location & Routing

Click Connector(O106)Body>Floor Wire>Rear Combination Light Assembly LH

O106-3 (B) - Body ground Brake pedal depressed 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY LH (STOP LIGHT CIRCUIT))

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE

w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE


NG

15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the O106 rear combination light assembly LH connector.


c.

Disconnect the O109 rear combination light assembly RH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O109)Location & Routing

Click Connector(O109)Body>Floor Wire>Rear Combination Light Assembly RH

O109-3 (B) - Body ground Brake pedal depressed 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY RH (STOP LIGHT CIRCUIT))

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE

w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE


NG

16.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
16.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the O106 rear combination light assembly LH connector.


c.

Disconnect the O109 rear combination light assembly RH connector.


d.

Disconnect the Q1 center stop light assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(Q1)Location & Routing

Click Connector(Q1)Body>Center Stop Light Cord Assembly>Center Stop Light Assembly

Q1-2 (B) - Body ground Brake pedal depressed 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

GO TO LIGHTING SYSTEM (CENTER STOP LIGHT ASSEMBLY (STOP LIGHT CIRCUIT))

Refer to "High mounted stop light does not illuminate" of problem symptoms table.

w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE

w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>PROBLEM SYMPTOMS TABLE


NG

17.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
17.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the O106 rear combination light assembly LH connector.


c.

Disconnect the O109 rear combination light assembly RH connector.


d.

Disconnect the Q1 center stop light assembly connector.


e.

Disconnect the A63 stop light switch assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A63,O106)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

Click Connector(O106)Body>Floor Wire>Rear Combination Light Assembly LH

A63-1 (OUT) - O106-3 (B) Always Below 1 Ω
A63-1 (OUT) or O106-3 (B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR