The entry and start system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (multiplex network body ECU) via CAN communication and the buzzer sounds.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.
After repair, confirm that no DTCs are output.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Wireless Door Lock Buzzer Answer-back Function | A |
| w/o Wireless Door Lock Buzzer Answer-back Function | B |
A
B
Check customize setting.
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Wireless Buzzer Response Function | Wireless buzzer response | Enable | $00:Disable,$01:Enable | Main body ECU (multiplex network body ECU) |
| Result | Proceed to |
|---|---|
| "Enable" is displayed | A |
| "Disable" is displayed | B |
A
B
Check that the function operates normally.
| Result | Proceed to |
|---|---|
| Wireless door lock function operates normally | A |
| Wireless door lock function does not operate normally | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Position Switch Status | Front door RH unlock detection switch signal | Lock or Unlock | Lock: Front door RH locked
Unlock: Front door RH unlocked |
- |
| FL Door Lock Position Switch Status | Front door LH unlock detection switch signal | Lock or Unlock | Lock: Front door LH locked
Unlock: Front door LH unlocked |
- |
| RR Door Lock Position Switch Status | Rear door RH unlock detection switch signal | Lock or Unlock | Lock: Rear door RH locked
Unlock: Rear door RH unlocked |
- |
| RL Door Lock Position Switch Status | Rear door LH unlock detection switch signal | Lock or Unlock | Lock: Rear door LH locked
Unlock: Rear door LH unlocked |
- |
| Tester Display |
|---|
| FR Door Lock Position Switch Status |
| FL Door Lock Position Switch Status |
| RR Door Lock Position Switch Status |
| RL Door Lock Position Switch Status |
The GTS display changes correctly in response to the lock/unlock operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not sound | A |
| Wireless door lock buzzer sounds | B |
A
B
Perform Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
Wireless door lock buzzer sounds
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A57 wireless door lock buzzer connector.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A57)Location & Routingewd_type=routing;type=c;code=A57 Click Connector(A57)Engine Compartment>Engine Room Main Wire>Wireless Door Lock Buzzerewd_type=component;type=c;code=A57;pinno=1,2 |
||
| A57-1 (B) - A57-2 (E) | Active Test Wireless Buzzer is OFF | Below 1 V |
| Active Test Wireless Buzzer is ON | Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V) |
|
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Reconnect the power distribution box assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A57)Location & Routingewd_type=routing;type=c;code=A57 Click Connector(A57)Engine Compartment>Engine Room Main Wire>Wireless Door Lock Buzzerewd_type=component;type=c;code=A57;pinno=1,2 |
||
| A57-1 (B) - MB-3 (BZR) | Always | Below 1 Ω |
| A57-2 (E) - Body ground | Always | Below 1 Ω |
| A57-1 (B) or MB-3 (BZR) - Other terminals and body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the 4D power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A57)Location & Routingewd_type=routing;type=c;code=A57 Click Connector(A57)Engine Compartment>Engine Room Main Wire>Wireless Door Lock Buzzerewd_type=component;type=c;code=A57;pinno=1 |
||
| A57-1 (B) - 4D-7 | Always | Below 1 Ω |
| A57-1 (B) or 4D-7 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to | |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C