The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1
*1: w/ Entry and Start System
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Position Switch Status | Front door RH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
- |
| FL Door Lock Position Switch Status | Front door LH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| RR Door Lock Position Switch Status | Rear door RH unlock detection switch signal | LOCK or UNLOCK | LOCK: Rear door RH locked
UNLOCK: Rear door RH unlocked |
- |
| RL Door Lock Position Switch Status | Rear door LH unlock detection switch signal | LOCK or UNLOCK | LOCK: Rear door LH locked
UNLOCK: Rear door LH unlocked |
- |
| Tester Display |
|---|
| FR Door Lock Position Switch Status |
| FL Door Lock Position Switch Status |
| RR Door Lock Position Switch Status |
| RL Door Lock Position Switch Status |
Normal conditions listed above are displayed.
| Result | Proceed to |
|---|---|
| OK | A |
| NG ("FR Door Lock Position Switch Status" is not normal) | B |
| NG ("FL Door Lock Position Switch Status" is not normal) | C |
| NG ("RR Door Lock Position Switch Status" is not normal) | D |
| NG ("RL Door Lock Position Switch Status" is not normal) | E |
A
B
C
D
E
OK
NG
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L11,H4)Location & Routingewd_type=routing;type=c,c;code=L11,H4 Click Connector(L11)Body>Front Door Wire LH / Television Camera Wire>Front Door Lock with Motor Assembly LHewd_type=component;type=c;code=L11;pinno=8,7 Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H4;pinno=9 |
||
| L11-8 (LSSR) - H4-9 (LSFL) | Always | Below 1 Ω |
| L11-7 (E) - Body ground | Always | Below 1 Ω |
| L11-8 (LSSR) - Body ground | Always | 10 kΩ or higher |
| H4-9 (LSFL) - Body ground | Always | |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
OK
NG
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K11,H4)Location & Routingewd_type=routing;type=c,c;code=K11,H4 Click Connector(K11)Body>Front Door Wire RH / Television Camera Wire>Front Door Lock with Motor Assembly RHewd_type=component;type=c;code=K11;pinno=7,8 Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H4;pinno=3 |
||
| K11-7 (LSSR) - H4-3 (LSFR) | Always | Below 1 Ω |
| K11-8 (E) - Body ground | Always | Below 1 Ω |
| K11-7 (LSSR) - Body ground | Always | 10 kΩ or higher |
| H4-3 (LSFR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/o Double Locking System) | A |
| OK (w/ Double Locking System) | B |
| NG | C |
A
B
C
Disconnect the H5 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M1,H5)Location & Routingewd_type=routing;type=c,c;code=M1,H5 Click Connector(M1)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RHewd_type=component;type=c;code=M1;pinno=6,9 Click Connector(H5)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H5;pinno=23 |
||
| M1-6 (LSSR) - H5-23 (LSWR) | Always | Below 1 Ω |
| M1-9 (E) - Body ground | Always | Below 1 Ω |
| M1-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| H5-23 (LSWR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the H5 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M1,H5)Location & Routingewd_type=routing;type=c,c;code=M1,H5 Click Connector(M1)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RHewd_type=component;type=c;code=M1;pinno=9,10 Click Connector(H5)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H5;pinno=23 |
||
| M1-9 (LSSR) - H5-23 (LSWR) | Always | Below 1 Ω |
| M1-10 (E) - Body ground | Always | Below 1 Ω |
| M1-9 (LSSR) - Body ground | Always | 10 kΩ or higher |
| H5-23 (LSWR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/o Double Locking System) | A |
| OK (w/ Double Locking System) | B |
| NG | C |
A
B
C
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(N1,H4)Location & Routingewd_type=routing;type=c,c;code=N1,H4 Click Connector(N1)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LHewd_type=component;type=c;code=N1;pinno=6,9 Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H4;pinno=10 |
||
| N1-6 (LSSR) - H4-10 (LSWL) | Always | Below 1 Ω |
| N1-9 (E) - Body ground | Always | Below 1 Ω |
| N1-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| H4-10 (LSWL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the H4 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(N1,H4)Location & Routingewd_type=routing;type=c,c;code=N1,H4 Click Connector(N1)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LHewd_type=component;type=c;code=N1;pinno=5,6 Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H4;pinno=10 |
||
| N1-5 (LSSR) - H4-10 (LSWL) | Always | Below 1 Ω |
| N1-6 (E) - Body ground | Always | Below 1 Ω |
| N1-5 (LSSR) - Body ground | Always | 10 kΩ or higher |
| H4-10 (LSWL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG