The power back door control switch signal is sent to the multiplex network door ECU.
If the power back door does not operate using the power back door control switch, a power back door control switch circuit malfunction is a possible cause.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
Check that the power back door function on the multi-information display in the combination meter assembly is set to ON.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>CUSTOMIZE PARAMETERS
| Result | Proceed to |
|---|---|
| Power back door function on the multi-information display in the combination meter assembly is set to ON (power back door system operation is permitted) | A |
| Power back door function on the multi-information display in the combination meter assembly is set to OFF (power back door system operation is prohibited) | B |
A
B
Check the power back door system condition.
| Result | Proceed to |
|---|---|
| The malfunction symptom reproduces | A |
| The malfunction symptom does not reproduce | B |
A
B
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>Power Back Door cannot be Operated Frequently
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Operation Switch (Instrument) | Power back door switch assembly signal | OFF or ON | OFF: Power back door control switch off
ON: Power back door control switch on |
- |
| Tester Display |
|---|
| Back Door Operation Switch (Instrument) |
The power back door control switch functions as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H132 power back door control switch connector.
Disconnect the H5 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H132,H5)Location & Routingewd_type=routing;type=c,c;code=H132,H5 Click Connector(H132)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Back Door Control Switchewd_type=component;type=c;code=H132;pinno=5,2 Click Connector(H5)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECUewd_type=component;type=c;code=H5;pinno=21 |
||
| H132-5 (CSW) - H5-21 (PBDS) | Always | Below 1 Ω |
| H132-2 (E) - Body ground | Always | Below 1 Ω |
| H132-5 (CSW) or H5-21 (PBDS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG