The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU (brake booster with master cylinder assembly).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C05621C | Brake Pedal Position Sensor Supply Voltage Circuit Voltage Out of Range | The sensor supply voltage (VCSK) is 4.7 V or less, or 5.3 V or more for 0.2 seconds or more. | ·
Open or short in brake pedal stroke sensor assembly power supply circuit ·
Improperly connected connector, deformation or corrosion of terminals ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake/EPB | A |
| C124B00 | Stroke Sensor Data Invalid | Sensor data is invalid for 0.2 seconds or more. (The sensor data of SKS1 and SKS2 is invalid.) | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor assembly |
Brake/EPB | A |
| C139251 | Zero Point Calibration of Stroke Sensor Not Programmed | The brake pedal stroke sensor assembly zero point calibration is not performed. (Normal brake pedal stroke sensor assembly zero point not memorized.) | Normal brake pedal stroke sensor assembly zero point not memorized. (Linear solenoid valve offset learning is not performed or Dealer Mode is not performed or not complete.) | Brake/EPB | A |
| P057A12 | Brake Pedal Position Sensor "A" Circuit Short to Battery | The sensor output voltage 1 (SKS1) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more. | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor assembly |
Brake/EPB | A |
| P057A14 | Brake Pedal Position Sensor "A" Circuit Short to Ground or Open | The sensor output voltage 1 (SKS1) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more. | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor assembly |
Brake/EPB | A |
| P057A1F | Brake Pedal Position Sensor "A" Circuit Intermittent | The difference between the current value and previous value of the sensor output voltage 1 (SKS1) is 8.5% or more for 0.2 seconds or more. | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor assembly |
Brake/EPB | A |
| P05DB12 | Brake Pedal Position Sensor "B" Circuit Short to Battery | The sensor output voltage 2 (SKS2) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more. | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor assembly |
Brake/EPB | A |
| P05DB14 | Brake Pedal Position Sensor "B" Circuit Short to Ground or Open | The sensor output voltage 2 (SKS2) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more. | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor assembly |
Brake/EPB | A |
| P05DB1F | Brake Pedal Position Sensor "B" Circuit Intermittent | The difference between the current value and previous value of the sensor output voltage 2 (SKS2) is 8.5% or more for 0.2 seconds or more. | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor assembly |
Brake/EPB | A |
| P05E062 | Brake Pedal Position Sensor "A"/"B" Signal Compare Failure | The difference in change between sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2) is excessively large for 0.2 seconds or more. (The comparison value of SKS1 and SKS2 is invalid.) | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor assembly |
Brake/EPB | A |
After replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Check the condition of each related circuit connector before troubleshooting.
Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.
Check and adjust the brake pedal height.
Adjust the brake pedal stroke sensor assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| Only C139251 is output | A |
| C05621C, C124B00, C139251, P057A12, P057A14, P057A1F, P05DB12, P05DB14, P05DB1F or P05E062 is output | B |
| None of the above conditions are met | C |
A
B
C
Perform system information memorization.
| Tester Display |
|---|
| Reset Memory |
| Tester Display |
|---|
| Calibration |
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None
Procedure1
Use the GTS, clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| Only C139251 is output | A |
| DTCs are not output | B |
| None of the above conditions are met | C |
Post-procedure1
None
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
C
Pre-procedure1
Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A27)Location & Routingewd_type=routing;type=c;code=A27 Click Connector(A27)Instrument Panel>Engine Room Main Wire>Brake Pedal Stroke Sensor Assemblyewd_type=component;type=c;code=A27;pinno=4,5,2,3 |
||
| A27-4 (VCSK) - A27-5 (SKG) | Ignition switch ON | 4.84 to 5.16 V |
| A27-2 (VSK2) - A27-3 (SKG2) | Ignition switch ON | 4.84 to 5.16 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A27 brake pedal stroke sensor assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A38,A27)Location & Routingewd_type=routing;type=c,c;code=A38,A27 Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assemblyewd_type=component;type=c;code=A38;pinno=13,17,19,21,25,33 Click Connector(A27)Instrument Panel>Engine Room Main Wire>Brake Pedal Stroke Sensor Assemblyewd_type=component;type=c;code=A27;pinno=5,6,1,2,4,3 |
||
| A38-13 (SKG1) - A27-5 (SKG) | Always | Below 1 Ω |
| A38-13 (SKG1) or A27-5 (SKG) - Body ground | Always | 10 kΩ or higher |
| A38-17 (SKS1) - A27-6 (SKS1) | Always | Below 1 Ω |
| A38-17 (SKS1) or A27-6 (SKS1) - Body ground | Always | 10 kΩ or higher |
| A38-19 (SKS2) - A27-1 (SKS2) | Always | Below 1 Ω |
| A38-19 (SKS2) or A27-1 (SKS2) - Body ground | Always | 10 kΩ or higher |
| A38-21 (VSK2) - A27-2 (VSK2) | Always | Below 1 Ω |
| A38-21 (VSK2) or A27-2 (VSK2) - Body ground | Always | 10 kΩ or higher |
| A38-25 (VSK1) - A27-4 (VCSK) | Always | Below 1 Ω |
| A38-25 (VSK1) or A27-4 (VCSK) - Body ground | Always | 10 kΩ or higher |
| A38-33 (SKG2) - A27-3 (SKG2) | Always | Below 1 Ω |
| A38-33 (SKG2) or A27-3 (SKG2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A27)Location & Routingewd_type=routing;type=c;code=A27 Click Connector(A27)Instrument Panel>Engine Room Main Wire>Brake Pedal Stroke Sensor Assemblyewd_type=component;type=c;code=A27;pinno=4,5,2,3 |
||
| A27-4 (VCSK) - A27-5 (SKG) | Ignition switch ON | 4.84 to 5.16 V |
| A27-2 (VSK2) - A27-3 (SKG2) | Ignition switch ON | 4.84 to 5.16 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG