Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C139A00  Brake Pressure Control solenoid Circuit Malfunction  C139B7E  Brake Pressure Control solenoid "A" Actuator Stuck On  C13CD00  Brake Pressure Too Low  C13CE00  Brake Pressure Too High  C140000  Brake Pressure Leak Malfunction  C14EC7E  Brake Pressure Control solenoid "C" Actuator Stuck On  C14F47E  Brake Pressure Control solenoid "D" Actuator Stuck On  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) controls braking force according to the hybrid control system regenerative braking force and provides the hydraulic pressure necessary for operating the master cylinder and each wheel cylinder according to the servo pressure sensor.

DTCs may be stored if one of the following occurs:

·

Brake fluid leaks.

·

Wheel cylinder vibrates due to uneven wear of a brake disc.

·

Foreign matter enters a solenoid valve.

·

Line pressure drops during air bleeding.

·

Brake pads are replaced.

·

Rotors are replaced.

HINT:

When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.



DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C139A00 Brake Pressure Control solenoid Circuit Malfunction Malfunction in one of the two circuits (leakage, etc.).
·

Brake fluid leaks

·

Uneven brake disc rotor wear

·

Brake actuator (brake booster with master cylinder assembly)


Brake/EPB A
C139B7E Brake Pressure Control solenoid "A" Actuator Stuck On SLA valve malfunction (stuck, etc.).
·

Brake fluid leaks

·

Uneven brake disc rotor wear

·

Brake actuator (brake booster with master cylinder assembly)


Brake/EPB A
C13CD00 Brake Pressure Too Low Fluid pressure control performance degraded (high pressure).
·

Brake fluid leaks

·

Uneven brake disc rotor wear

·

Brake actuator (brake booster with master cylinder assembly)


Brake/EPB A
C13CE00 Brake Pressure Too High Fluid pressure control performance degraded (low pressure).
·

Brake fluid leaks

·

Uneven brake disc rotor wear

·

Brake actuator (brake booster with master cylinder assembly)


Brake/EPB A
C140000 Brake Pressure Leak Malfunction Malfunction (leakage, etc.) detected in the ABS decrease pressure valve in the brake actuator assembly. Brake actuator assembly Brake/EPB A
C14EC7E Brake Pressure Control solenoid "C" Actuator Stuck On SSA valve malfunction (stuck, etc.).
·

Brake fluid leaks

·

Uneven brake disc rotor wear

·

Brake actuator (brake booster with master cylinder assembly)


Brake/EPB A
C14F47E Brake Pressure Control solenoid "D" Actuator Stuck On SGH valve malfunction (stuck, etc.).
·

Brake fluid leaks

·

Uneven brake disc rotor wear

·

Brake actuator (brake booster with master cylinder assembly)


Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake booster with master cylinder assembly or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA
a.

Interview the customer to check the vehicle conditions when the brake system warning light (yellow indicator) illuminated.


b.

Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.

HINT:
·

Freeze Frame Data is only stored once when a DTC is stored.

·

If other DTCs are output, repair any malfunctions related to those DTCs first, and then reproduce the conditions that caused any of the DTCs to be stored based on the interview with the customer.



Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR FLUID LEAK
2.CHECK FOR FLUID LEAK
a.

Check that there are no fluid leaks in the brake lines between the brake booster with master cylinder assembly and the wheel cylinders.


b.

Check that there is no brake fluid leaks from the brake booster with master cylinder assembly or brake actuator assembly body.


c.

Check that the brakes are not dragging.

OK:

There are no fluid leaks or dragging.



Result:
Proceed to
OK
NG



OK

3.PERFORM AIR BLEEDING

NG

REPAIR OR REPLACE APPLICABLE PART

3.PERFORM AIR BLEEDING
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Perform the air bleeding procedure in Bleed Brake System.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model TMC Made)>BLEEDING



Result:
Proceed to
NEXT



NEXT

4.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE ACTUATOR ASSEMBLY (ACTUATOR SIDE)
4.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE ACTUATOR ASSEMBLY (ACTUATOR SIDE)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector 2 minutes after the ignition switch is turned off.


b.

Disconnect the A95 brake actuator assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.


Result:
Result Proceed to
OK A
NG (skid control ECU (brake booster with master cylinder assembly)) B
NG (brake actuator assembly) C



Post-procedure1

a.

None



A

5.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

5.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

Pre-procedure1

a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A95 brake actuator assembly connector.


Procedure1

a.

Measure the voltage and resistance on the wire harness side.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>TERMINALS OF ECU


OK:

Voltage and resistance readings are all normal.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Disconnect the A95 brake actuator assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A38,A95)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A38-14 (+BS) - A95-5 (+BS) Always Below 1 Ω
A38-14 (+BS) or A95-5 (+BS) - Body ground Always 10 kΩ or higher
A38-48 (SFRH) - A95-28 (SFRH) Always Below 1 Ω
A38-48 (SFRH) or A95-28 (SFRH) - Body ground Always 10 kΩ or higher
A38-49 (SFLH) - A95-31 (SFLH) Always Below 1 Ω
A38-49 (SFLH) or A95-31 (SFLH) - Body ground Always 10 kΩ or higher
A38-50 (SRRH) - A95-30 (SRRH) Always Below 1 Ω
A38-50 (SRRH) or A95-30 (SRRH) - Body ground Always 10 kΩ or higher
A38-51 (SRLH) - A95-29 (SRLH) Always Below 1 Ω
A38-51 (SRLH) or A95-29 (SRLH) - Body ground Always 10 kΩ or higher
A38-44 (SFRR) - A95-18 (SFRR) Always Below 1 Ω
A38-44 (SFRR) or A95-18 (SFRR) - Body ground Always 10 kΩ or higher
A38-45 (SFLR) - A95-15 (SFLR) Always Below 1 Ω
A38-45 (SFLR) or A95-15 (SFLR) - Body ground Always 10 kΩ or higher
A38-46 (SRRR) - A95-16 (SRRR) Always Below 1 Ω
A38-46 (SRRR) or A95-16 (SRRR) - Body ground Always 10 kΩ or higher
A38-47 (SRLR) - A95-17 (SRLR) Always Below 1 Ω
A38-47 (SRLR) or A95-17 (SRLR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C139B7E, C13CD00 or C13CE00 is output A
Only C139A00 is output B
C14EC7E or C14F47E is output C
Only C140000 is output D



A

8.READ VALUE USING GTS (SERVO PRESSURE)

B

12.READ VALUE USING GTS (SERVO PRESSURE)

C

17.CLEAR DTC

D

19.INSPECT BRAKE PEDAL STROKE SENSOR ASSEMBLY OUTPUT VOLTAGES AND WHEEL CYLINDER PRESSURE
8.READ VALUE USING GTS (SERVO PRESSURE)

Pre-procedure1

a.

Connect an LSPV gauge set.


Procedure1

a.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 2.10 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake/EPB > Data List
Tester Display
Servo Pressure
50003 435 210

b.

Depress the brake pedal slowly and check the servo pressure output values with respect to the wheel cylinder pressure values for each wheel.

Standard Pressure:
Servo Pressure (for Front Right Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3

Servo Pressure (for Front Left Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

9.CHECK BRAKE DISC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.CHECK BRAKE DISC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the A27 brake pedal stroke sensor assembly connector.


Procedure1

a.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

Uneven disc wear can be checked by measuring the disc thickness variation.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

10.CLEAR DTC

NG

REPLACE BRAKE DISC

10.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A27 brake pedal stroke sensor assembly connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC

Pre-procedure1

a.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


b.

Turn the ignition switch off and wait for 3 minutes or more.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C139B7E, C13CD00 and C13CE00 are not output A
C139B7E, C13CD00 or C13CE00 is output B


HINT:

If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

12.READ VALUE USING GTS (SERVO PRESSURE)

Pre-procedure1

a.

Connect an LSPV gauge set.


Procedure1

a.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 2.10 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake/EPB > Data List
Tester Display
Servo Pressure
50003 435 210

b.

Depress the brake pedal slowly and check the servo pressure output values with respect to the wheel cylinder pressure values for each wheel.

Standard Pressure:
Servo Pressure (for Front Right Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3

Servo Pressure (for Front Left Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

13.CHECK BRAKE DISC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

13.CHECK BRAKE DISC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the A27 brake pedal stroke sensor assembly connector.


Procedure1

a.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

Uneven disc wear can be checked by measuring the disc thickness variation.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

14.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)

NG

REPLACE BRAKE DISC

14.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A27 brake pedal stroke sensor assembly connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

Pre-procedure2

a.

Turn the ignition switch off.


b.

Mount a pedal effort gauge.


Procedure2

a.

Turn the ignition switch to ON (READY) and depress the brake pedal once.

HINT:

Depress the brake pedal after turning the ignition switch ON (READY) to set the vehicle to linear mode (switching solenoid (SSA) on).



b.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor assembly Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor assembly 2 Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Chassis > Brake/EPB > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 435 207,208

c.

Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.

NOTICE:

Perform this procedure in linear mode (switching solenoid (SSA) on).


Standard Voltage:
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Stroke Sensor2
[V]
50 (5, 11.2) 1.15 to 1.85 3.15 to 3.85
100 (10, 22.5) 1.30 to 2.00 3.00 to 3.70
200 (20, 45.0) 1.49 to 2.19 2.81 to 3.51
500 (51.0, 112.4) 1.60 to 2.30 2.70 to 3.40


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

15.CLEAR DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

15.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

16.RECONFIRM DTC
16.RECONFIRM DTC

Pre-procedure1

a.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


b.

Turn the ignition switch off and wait for 3 minutes or more.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C139A00 is not output A
C139A00 is output B


HINT:

If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

17.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

18.RECONFIRM DTC
18.RECONFIRM DTC

Pre-procedure1

a.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


b.

Turn the ignition switch off and wait for 3 minutes or more.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C14EC7E and C14F47E are not output A
C14EC7E or C14F47E is output B


HINT:

If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

19.INSPECT BRAKE PEDAL STROKE SENSOR ASSEMBLY OUTPUT VOLTAGES AND WHEEL CYLINDER PRESSURE

Pre-procedure1

a.

Mount a pedal effort gauge.


b.

Disconnect the A30 brake booster pump assembly connector.


Procedure1

a.

Depress the brake pedal 10 times or more until it becomes hard.

HINT:

Depressing the brake pedal with the connector of the brake booster pump assembly disconnected drops the accumulator pressure to approximately 0 MPa.



Pre-procedure2

a.

Connect an LSPV gauge set.


Procedure2

a.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Chassis > Brake/EPB > Data List
Tester Display
Stroke Sensor
50003 435 207

b.

Slowly depress the brake pedal and check the brake pedal stroke sensor assembly output voltages and the wheel cylinder pressure with respect to brake pedal depression force.

NOTICE:

Check the wheel cylinder pressure with the switching solenoid (SSA, SGH) off and an accumulator pressure of 0 MPa.


Standard Pressure:
for Front Right Wheel
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
200 (20, 45.0) 1.23 to 1.93 0.06 to 2.06 (0.6 to 21.0, 9 to 299)
500 (51, 112.4) 1.42 to 2.12 2.09 to 4.09 (21.3 to 41.7, 303 to 593)

for Front Left Wheel
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
200 (20, 45.0) 1.23 to 1.93 0.06 to 2.06 (0.6 to 21.0, 9 to 299)
500 (51, 112.4) 1.42 to 2.12 2.09 to 4.09 (21.3 to 41.7, 303 to 593)


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

20.CLEAR DTC

NG

20.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A30 brake booster pump assembly connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

21.RECONFIRM DTC
21.RECONFIRM DTC

Pre-procedure1

a.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


b.

Turn the ignition switch off and wait for 3 minutes or more.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C140000 is not output A
C140000 is output B


HINT:

If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE



Post-procedure1

a.

None



A

B