Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483473 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  Downhill Assist Control Indicator Light does not Come ON  


DESCRIPTION

Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:

·

Check that the shift lever is in P.

·

The vehicle speed is 25 km/h (16 mph) or more.

·

The brake system is malfunctioning.

·

Temperature of the brake actuator assembly increases and the downhill assist control is temporarily canceled.


WIRING DIAGRAM

C408613E04
5.542,0.5 6.156,0.698 0.615,0.198 10 false CANH 0.823,0.531 1.24,0.729 0.417,0.198 10 false CANH 5.271,0.333 5.469,0.583 0.198,0.25 10 false 5 1.333,0.323 1.531,0.573 0.198,0.25 10 false 9 0.833,1.094 1.25,1.292 0.417,0.198 10 false CANL 5.531,1.094 5.948,1.292 0.417,0.198 10 false CANL 5.198,0.896 5.396,1.146 0.198,0.25 10 false 19 1.333,0.906 1.531,1.156 0.198,0.25 10 false 25 5.531,2.135 5.948,2.333 0.417,0.198 10 false GND1 5.208,1.99 5.406,2.24 0.198,0.25 10 false 46 0.313,1.719 0.698,1.958 0.385,0.24 10 false H6 5.552,3.719 6.052,4.01 0.5,0.292 10 false HDCS 5.26,3.719 5.458,3.969 0.198,0.25 10 false 8 2.24,4.406 4.833,4.792 2.594,0.385 10 false Downhill Assist Control Switch Assembly 2.229,4.24 2.896,4.563 0.667,0.323 10 false H133 5.458,4.74 5.823,4.99 0.365,0.25 10 false A39 5.448,4.896 7.01,5.313 1.563,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 0.542,5.313 2.708,5.646 2.167,0.333 10 false : CAN Communication Line 0.302,1.896 1.479,2.333 1.177,0.438 10 false Combination Meter Assembly 2.552,3.719 2.854,3.969 0.302,0.25 10 false 2 3.646,3.708 3.938,3.969 0.292,0.26 10 false 5 6.615,3.844 6.969,4.115 0.354,0.271 10 false IC 3.406,3.719 3.698,3.979 0.292,0.26 10 false B 2.74,3.729 3.031,3.99 0.292,0.26 10 false E

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY


PROCEDURE

1.INSPECT DOWNHILL ASSIST CONTROL SWITCH ASSEMBLY

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>INSPECTION

OK:

The downhill assist control switch operates normally.


Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH ASSEMBLY)

NG

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH ASSEMBLY)
a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A39,H133)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(H133)Instrument Panel>Instrument Panel Wire / Speaker Wire>Downhill Assist Control Switch

A39-8 (HDCS) - H133-5 (B) Always Below 1 Ω
A39-8 (HDCS) or H133-5 (B) - Body ground Always 10 kΩ or higher
H133-2 (E) - Body ground Always Below 1 Ω


Result:
Result
OK
NG




OK

3.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Downhill Assist Control Indicator
50004 409 119

b.

Check the combination meter assembly.

OK:

The Downhill assist control indicator light turns on or off in accordance with the GTS.



Result:
Proceed to
OK
NG



OK

NG