| *A | for TMMF Made | *B | for TMC Made |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent | ★ | Precoated part |
| *A | for Driver Side | *B | for Passenger Side |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent | - | - |
| *A | for Passenger Side | *B | for Driver Side |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
MP grease | - | - |
| *A | for Passenger Side | *B | for Driver Side |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |
|
MP grease |
|
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent | ★ | Precoated part |
Use the same procedure for the LH side and RH side.
The following procedure is for the RH side.
67837B
1.INSTALL FRONT DOOR DUST PROOF SEAL (for TMMF Made)
67837B
2.INSTALL FRONT DOOR DUST PROOF SEAL (for TMC Made)
|
|
75926
4.INSTALL NO. 3 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Front Door)>INSTALLATION
75922M
5.INSTALL NO. 1 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Front Door)>INSTALLATION
67001A
6.INSTALL FRONT DOOR PANEL CUSHION
67862
7.INSTALL FRONT DOOR WEATHERSTRIP
68620
8.INSTALL FRONT DOOR CHECK ASSEMBLY
| *A | When reusing a bolt | - | - |
| *a | Bolt A | *b | Bolt B |
Clean the bolt hole in the vehicle body.
When reusing a bolt:
1. Clean the threads of the bolt A, with non-residue solvent.
2. Apply adhesive to the threads of the bolt A.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the front door check assembly with the bolt A and 2 bolts B.
67496C
9.INSTALL FRONT DOOR FRONT LOWER FRAME COVER UPPER
87940
10.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY
for TMC Made
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMC Made)>INSTALLATION
for TMMF Made
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMMF Made)>INSTALLATION
67836J
11.INSTALL NO.2 FRONT DOOR SERVICE HOLE SEAL
for TMC Made
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMC Made)>INSTALLATION
for TMMF Made
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMMF Made)>INSTALLATION
75074
12.INSTALL FRONT DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY
13.INSTALL HOLE COVER
68210C
14.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>INSTALLATION
69312
15.INSTALL FRONT DOOR LOCK OPEN ROD
69202A
16.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
| *A | w/ Entry and Start System | - | - |
|
MP grease |
|
Install in this Direction |
Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.
Engage the guides to install the front door outside handle frame sub-assembly as shown in the illustration.
Engage the guides to install the front door outside handle frame sub-assembly as shown in the illustration.
Using a T30 "TORX" socket wrench, tighten the screw.
w/ Entry and Start System:
1. Engage the clamp to install the wire harness.
69318C
17.INSTALL DOOR LOCK WIRING HARNESS SEAL
69040A
18.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY
69242H
19.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD
69241H
20.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD
21.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Install the front door lock cylinder assembly.
Check that the front door lock cylinder assembly is inserted into the front door lock with motor assembly.
Using a T30 "TORX" socket wrench, tighten the screw.
69217D
22.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Engage the claws and guides to install the front door outside handle cover.
Using a T30 "TORX" socket wrench, tighten the screw.
23.INSTALL HOLE PLUG
69220
24.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY
67402F
25.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
| *a | Bolt A | *b | Bolt B |
Install the front door front lower frame sub-assembly with the bolt A and bolt B.
67404F
26.INSTALL FRONT DOOR REAR DOOR FRAME SUB-ASSEMBLY
68151C
27.INSTALL FRONT DOOR GLASS RUN
69820
28.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
|
MP grease | - | - |
Apply MP grease to the sliding parts of the front door window regulator assembly.
Install the front door window regulator assembly with the 6 nuts.
Connect the connector.
68102
29.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
| *A | for Driver Side | *B | for Front Passenger Side |
for Driver Side:
1. Connect the multiplex network master switch assembly.
for Front Passenger Side:
1. Connect the power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolt holes can be seen.
| *A | for Driver Side | *B | for Front Passenger Side |
Disconnect the cable from the negative (-) auxiliary battery terminal.
for Front Passenger Side:
1. Disconnect the power window regulator switch assembly.
for Driver Side:
1. Disconnect the multiplex network master switch assembly.
Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.
Be careful not to damage the front door glass sub-assembly.
Install the front door glass sub-assembly with the 2 bolts.
Install the hole plug.
8983AA
30.INSTALL SIDE AIR BAG PRESSURE SENSOR
67832
31.INSTALL FRONT DOOR SERVICE HOLE COVER
Pass the front door lock remote control cable assembly, front door inside locking cable assembly and wire harness through front door service hole cover.
Engage the clips to install the front door service hole cover.
Engage the clamp and guide.
Insert the 3 front door service hole cover clips and turn them 45° as shown in the illustration.
86160P
32.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
67856B
33.INSTALL FRONT DOOR PANEL PROTECTOR
67838A
34.INSTALL FRONT DOOR VENT SEAL
68172A
35.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP
Install the front door glass inner weatherstrip with the front door panel protector and front door vent seal.
69284C
36.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
69206B
37.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
67602
38.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
67656
39.INSTALL FRONT DOOR TRIM GARNISH
40.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
41.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
67492A
42.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH
43.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
44. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
46.INITIALIZE POWER WINDOW CONTROL SYSTEM